Bedienungsanleitung Trotec PMTS01-230V (Seite 18 von 21) (Englisch)

753364

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

18 EN

170W multi-function tool PMTS 01-230V

The device becomes hot:

• Make sure not to exert too much pressure on the device

during grinding.

• Select a lower speed by turning the setting wheel for

speed selection(1) to a low level.

• Check whether the tool is suitable for the tasks to be

carried out.

• Keep the venting slots clear to prevent the motor from

overheating.

Info

Wait for at least 10 minutes before switching the

device back on.

The tool is loose:

• Make sure that the clamping nut(39) is tightened properly

to the tool holder.

The cutting disc has difficulties with penetrating the

material to be processed or the cutting performance of the

abrasive wheel is insufficient:

• Check whether the chosen tool is suitable for the material

to be processed.

• Check the set speed; it must be suitable for both the tool

and the material.

• Select a higher speed by turning the setting wheel for

speed selection(1) to a higher level.

• If the cutting disc or abrasive wheel is worn, replace it with

a new one.

The device is running but the flexible shaft does not work:

• Check whether the inner axis(30) of the flexible shaft is

fixed firmly in the tool holder(27).

Your device still does not operate correctly after these

checks?

Please contact the customer service. If necessary, bring the

device to an authorised specialist electrical company or to

Trotec for repair.

Maintenance

Activities required before starting maintenance

Warning of electrical voltage

Do not touch the mains plug with wet or damp hands.

• Switch off the device.

• Hold onto the mains plug while pulling the power cable out

of the mains socket.

• Allow the device to cool down completely.

Warning of electrical voltage

Maintenance tasks which require the housing to be

opened must only be carried out by authorised

specialist companies or by Trotec.

Notes on maintenance

Inside the device, there are no parts that need to be lubricated

by the user.

Cleaning

The device should be cleaned before and after each use.

Note

The device does not have to be lubricated after

cleaning.

Warning of electrical voltage

There is a risk of a short-circuit due to liquids

penetrating the housing!

Do not immerse the device and the accessories in

water. Make sure that no water or other liquids can

enter the housing.

• Clean the device with a soft, damp and lint-free cloth.

Make sure that no moisture enters the housing. Protect

electrical components from moisture. Do not use any

aggressive cleaning agents such as cleaning sprays,

solvents, alcohol-based or abrasive cleaners to dampen

the cloth.

• Dry the device with a soft, lint-free cloth.

• Remove any abrasive dust and, if applicable, wood chips

from the tool holder.

• Keep the ventilation openings free from dust deposits to

prevent overheating of the motor.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PMTS01-230V Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PMTS01-230V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info