Bedienungsanleitung Trotec PRDS05-230V (Seite 4 von 18) (Englisch)

753296

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

4 EN

rotary hammer PRDS 05-230V

•Disconnect the plug from the power source and/or

remove the battery pack, if detachable, from the power

tool before making any adjustments, changing

accessories, or storing power tools. Such preventive

safety measures reduce the risk of starting the power tool

accidentally.

•Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

•Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage of

parts and any other condition that may affect the

power tool's operation. If damaged, have the power

tool repaired before use. Many accidents are caused by

poorly maintained power tools.

•Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to

bind and are easier to control.

•Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

•Keep handles and grasping surfaces dry, clean and

free from oil and grease. Slippery handles and grasping

surfaces do not allow for safe handling and control of the

tool in unexpected situations.

General Power Tool Safety Warnings– Service

•Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Device-specific safety warnings for rotary hammers

Wear ear protectors when impact drilling. Exposure

to noise can cause hearing loss.

•Use the additional handle pre-assembled at the device.

Losing control of the power tool may result in personal

injury.

•Hold the power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory or fasteners may contact hidden wiring or

its own cord. Cutting accessory contacting a "live" wire

may make exposed metal parts of the power tool "live"

and could give the operator an electric shock.

•Use appropriate detection equipment to track down

concealed supply lines or consult the local utility

companies. Contact with electrical lines may result in fire

and electric shock. Damaging a gas line may lead to an

explosion. Penetrating a water line causes property

damage and may cause an electric shock.

•Vibrations can be harmful to the human hand-arm

system. Keep the vibration exposure time to a minimum.

•During operation hold onto the power tool with both

hands. Make sure that you stand firmly on the ground. It is

safer to handle the power tool with two hands.

•Secure the workpiece. The grip of tensioning devices or a

vice is more secure than holding the workpiece only by

hand.

Protect yourself and others present from injuries

caused by splintering and flying bits and pieces.

Wear a hard hat, eye protection, a dust mask and safety

boots. If necessary, put up partition panels as shield

against breaking off debris.

•Before starting to work, always make sure that the

insertion tool is firmly clamped inside the drill chuck.

Insertion tools that are not locked in place could be

catapulted out of the power tool upon switch-on and lead

to injuries.

•Before switching on the power tool, ensure that the

insertion tool can move freely. If the device is switched

on with a jammed insertion tool, the resulting forces can

be extreme causing the device to kick out sideways.

•Immediately switch off the power tool if the insertion

tool blocks. The power tool can lash out to the side owing

to the forces that build up consequently.

•Regularly check the drill chuck for wear or damage.

•Only start a percussive power tool while holding it

against a workpiece (wall, ceiling, etc.).

•Wait until the power tool has come to a standstill,

before putting it down.

Safety instructions when using long drill bits

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PRDS05-230V Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PRDS05-230V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info