489379

Truma B 10 Seite 7

7
Zoom out
Zoom in
Vorherige Seite
1/24
Nächste Seite
7
Screw the boiler securely to the floor of the vehicle with
at least two shackle plates (11) with the screws provided,
B 5.5 x 25, on a suitable base (plywood panel, laminated
wood strips, or metal base).
Water connection
All pressure and submergible pumps up to 2.8 bar are used
for operating the boiler and all mixed combination sets with
or without an electrical switch.
Fig. B
When using immersion pumps, a non-return valve (12 – not
included in the scope of supply) must be fitted between the
pump and the first branch point (arrow points in direction of
flow).
Fig. C
When using pressure pumps with high switching hysteresis,
hot water may flow back through the cold water tap. To pre-
vent the backflow, we recommend that a non-return valve
(6 – not included in the scope of supply) be fitted between the
outlet to the cold water tap and the drain valve.
Pressure and hot water-resistant hoses with an internal diam-
eter of 10 mm should be used for the boiler and the safety/
drain valve connections.
For non-flexible pipe routing (e.g. John Guest System) Truma
can supply the water connections (15 + 16), the safety/drain
valve (13) and a non-return valve (12 + 6) with a 12 mm diam-
eter inner connection as accessories.
If connecting to a central water supply (rural or city connec-
tion) or when using more powerful pumps, a pressure reducer
must be used which prevents pressures of greater than
2.8 bar occurring in the boiler.
Route the water hoses so that they are as short and
free of kinks as possible. All hose connections must be
secured using hose clamps (also for cold water)! Pressures
of up to 3.5 bar can occur in the safety/drain valve (also in
submergible pumps) because of the heat of the water and the
resulting expansion.
Hose clips (part no. 40712-01) are recommended for attaching
the hoses to the wall or the floor. If gas heating has been in-
stalled, the water hoses and the hose clips can be laid on the
hot air pipes, which prevents frost.
In order to guarantee that the boiler is completely emp-
ty, the enclosed elbow with breather valve (fig. D: 15)
must be used for the hot water connection!
All hot water pipes should be routed in a descending
manner to the safety/drain valve! Otherwise no guar-
antee of protection from frost!
Installation of safety/drain valve
Fig. B + C
Install safety/drain valve (13) at a place which is easily accessi-
ble, near the water heater. Drill hole with 18 mm diameter and
pass through discharge socket with hose (14). Fasten safety/
drain valve with 2 screws. The draining is to be directly to the
outside (apply splash guard, if necessary).
Water pipe routing
Fig. B + C
Connect cold water supply (24) to safety/drain valve (13).
Direction of flow is unimportant.
Fig. D
Screw elbow with integrated breather valve (15) to hot water
connection pipe (upper pipe) and elbow without breather
valve (16) to cold water connecting pipe (lower pipe).
Slide on nut (17), tension ring (18) and O-ring (19). Assemble
screw connector and connecting pipe and fasten together
using nut (17).
Slide ventilation hose with 11 mm outer diameter (20) onto
the breather valve hose nozzle (21) and route towards the out-
side. Do not allow the radius of the arc to be less than 40 mm.
Cut off the ventilation hose approx. 20 mm below the floor of
the vehicle at an angle of 45° to the direction of travel.
Fig. B + C
Produce hose connection (22) for cold water supply between
safety/drain valve (13) and elbow (16 – lower pipe) on boiler.
Route the hot water pipe (23) from the elbow with integrated
breather valve (15 – upper pipe) to the hot water consumers.
Installation of the control panels
When using control panels which are specific to the ve-
hicle or the manufacturer, the electrical connection must
be established in accordance with the Truma interface descrip-
tions. Any modification made to the Truma components per-
taining to this will lead to the invalidation of the guarantee, as
well as to the exclusion of any claims for liability. The installer
(manufacturer) is responsible for providing instructions for use
for the user as well as for identification printing on the control
panels!
When selecting the location, bear in mind that the control
panels must not be subjected to direct radiant heat. Length of
connection cable 2.5 m. If required, a cable extension of 5 m
can be supplied (part no. 70000-53500).
If flush mounting is not possible, Truma will supply an
on-surface frame (25 – part no. 40000-52600) as an
accessory on request.
Fig. E
The control panel for gas operation (26) and (if provided) the
control panel for electrical operation (27) should be fitted next
to one another if at all possible (distance between centres of
holes 66 mm).
In each case, drill a hole with diameter 55 mm (distance
between centres of holes 66 mm).
Plug the control panel cable (28) to the control panel for gas
operation (26) and then fit on the rear cover cap (29) as a
stress-relieving device.
Push the cable through to the rear and lay the connection
cable (28 + 30) to the boiler.
Lay the connection cable with the orange multipole con-
nector (28) to the 12 V control electronics unit (fig. F – for
connection see “Electrical connection 12 V”).
Secure both control panels with 4 screws (31) each and fit the
cover frame (32) on them.
Truma offers side parts (32) in eight different colors for
finishing the cover frames (33) in a visually pleasing way.
Please ask your dealer.
… 7 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

truma-b-10

Suche zurücksetzen

  • Wir haben uns einen Fendt Diamant 2013 gekauft, leider heizt der Boiler nicht über
    230 V.Kann mir jemand einen Tip geben, ob noch irgendwo eine Sicherung ist.Wenn Ich den Schalter betätige, klickt es im Kleiderschrank.
    Vielen Dank Eingereicht am 22-7-2020 14:13

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Truma B 10 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Truma B 10

Truma B 10 Bedienungsanleitung - Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch - 44 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info