Bedienungsanleitung Truma Mover H TE R (Seite 15 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch)

484651

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Remote hand set LED flash codes and

acoustic signal

LED “On” and no acoustic signal

System is ready for operation

LED “Off” and no acoustic signal

System off

(check remote hand set batteries if necessary)

LED “flashes” in combination with acoustic signal

for approx. 5 seconds after switching the remote hand set

on, until the system is ready for operation.

for approx. 10 seconds after switching the remote hand set

on, then it is switched off again – 13-pin safety plug not

connected to safety socket or unable to establish radio link

to controller.

every 3 seconds if the caravan battery has a low charge

(finish manoeuvring as quickly as possible and charge

battery).

5 times a second (5 Hz) if the caravan battery voltage is

low. No manoeuvring is possible until the battery voltage is

above 11 V again (e.g. by means of recovery / battery charg-

ing). The drive rollers can also be disengaged with a voltage

of less than 11 V.

approx. 2 times per second with overcurrent / over-

temperature (2 Hz). Switch remote hand set off and on

again (wait for cooling down if necessary in the event of

overtemperature).

Changing the batteries in the remote handset

Please be sure to use leak proof micro-

batteries only, type LR 03, AAA, AM 4,

MN 2400 (1.5 V).

When fitting new batteries

ensure the polarity is correct!

Dead and used batteries may

leak and damage the remote

handset! Remove the batteries if the

handset is not going to be used for an

extended period.

No claims under guarantee will be considered for damage

caused by leaking batteries.

Before throwing away a defective handset, it is essential that

the batteries are removed and disposed of in proper manner.

Manoeuvring the caravan

Please read the “Safety instructions” before using

the Mover®!

Apply handbrake with caravan uncoupled.

Unplug 13-pin plug from vehicle and plug into safety socket of

caravan.

For safety reasons the Mover® can only be operated if

the 13-pin plug of the caravan has been plugged into the

safety socket.

In the event of an error, the 13-pin plug should not be

removed from the safety socket as otherwise the elec-

tronic protection function is deactivated.

If there is a fault in both caravan brake lights, the power

circuit of the safety socket is not closed. In this case the

Mover® cannot be operated.

–

Switch remote hand set on – green LED flashes for 5 seconds

in combination with the acoustic alarm until the control unit is

ready for operation.

Simultaneously press the two buttons (h) for engaging, which

starts after approx. 3 seconds (safety delay).

Use the position indicator to check whether both drive

rollers have been correctly applied (arrow of yellow posi-

tion indicator is above the line that is closest to the tyre).

Before operating the Mover®, release the handbrake.

The six direction buttons provide movement in six directions –

forward, reverse, left forward, left reverse, right forward, right

reverse.

With the Mover® H SE R, the “left forward” (e) and “right re-

verse” (f) or “right forward” (d) and “left reverse” (g) buttons

can also be pressed simultaneously in order to turn the cara-

van in a circle on the spot without moving it forwards.

The soft start / stop facility means that the caravan starts

without jerking and is gently braked when stopping.

If the buttons are released or the radio signal is interfered with

or becomes too weak, the caravan stops. Your Mover® cannot

be activated by radio devices or other Mover® remote hand

sets.

After starting up, the Mover® moves at a uniform speed. The

speed will increase a little when going downhill and decrease

a little when going uphill.

After manoeuvring, first apply the handbrake and then

disengage the drive rollers from the tyres.

Move slide switch on remote control to the “Off” £ position

to switch the remote control and the Mover® off.

The slide switch also acts as an “Emergency stop”

switch.

Remove plug from safety socket after manoeuvring, otherwise

the battery will be discharged. Standby current with plug in-

serted approx. 200 mA.

Hitching to a tow car

It is totally possible to position the caravan’s hitch to a station-

ary car tow ball using the Mover®, but take some care.

Use the instructions above as your guide. Use the button con-

trols to bring the caravan to the car (car handbrake “ON“, and

car in gear). Use a button stabbing technique to exactly posi-

tion the hitch directly over the ball. Lower the hitch to the ball

and engage in the normal way using the jockey wheel.

Prepare the caravan for towing as usual. The caravan must

never be towed with the drive rollers engaged.

Maintenance

Please do not allow the drive units to become soiled with

coarse road material. When you are cleaning the caravan,

spray the Mover® with a water hose to dissolve mud etc.

Please ensure that no stones, twigs or the like become

trapped in the equipment. The control unit does not require

maintenance. Please keep the remote hand set in a dry place.

Every year (and/or before putting away for the winter), clean

Mover® as described, dry and lightly spray the drive unit

guides with oil spray or a similar water-repelling lubricant.

Do not put lubricant on the rollers or the tyres! Engage

and disengage the drive units several times to allow the lubri-

cant to penetrate all the guides. Do not park the caravan with

the drive rollers engaged.

Truma Mover H TE R Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info