Bedienungsanleitung Truma Mover H TE R (Seite 16 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch)

484651

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Synchronising the electronic control unit with

the radio remote hand set

The remote hand set and the control unit are synchro-

nised with each other in the factory.

If the control unit or the remote hand set is replaced, they

must be re-synchronised as described below.

1. Check the installation in accordance with the installation

instructions and ensure that the drive rollers are not applied.

Check that the battery is properly connected, check the condi-

tion of the battery and that a voltage of 12 V is present at the

control unit. Please ensure that the caravan plug has been

plugged into the safety socket.

2. Press the reset button (k) on the control unit and hold down

(red LED – j – flashes slowly), and after approx. 5 seconds the

LED (j) starts to flash rapidly. Then release the reset button

and press and hold down the caravan reverse button on the

remote hand set (c) within 10 seconds, simultaneously switch-

ing on the remote hand set using the slide switch (a).

The remote hand set and the control unit are synchronised to

each other. After successful synchronisation, the red LED

flashes rapidly.

Technical data

Operational voltage

12 V DC

Current consumption

average approx. 35 A maximum 150 A

Stand by consumption

< 1 mA (when the plug is disconnected)

Remote hand set frequency

Class 1, 868 MHz

Speed

approx. 17 cm per second (depending on weight and incline)

Weight

Mover® H SE R / H TE R approx. 26 kg

Angle brackets (1 pair), depending on the model 5 – 6 kg

Fuse engagement motors

Blade fuse 20 A

Fuse in positive supply cable

150 A

Area of operation Mover® H SE R

Single axle caravans with a total weight up to 2000 kg

Area of operation Mover® H TE R

Dual axle caravans with a total weight up to 2250 kg

Right to effect technical modifications reserved!

To prevent the battery from becoming totally discharged

during long periods of inactivity it must be disconnected and

recharged before using again. Charge the caravan battery

before starting up.

It is extremely easy for you or your caravan dealer to perform

the checking and maintenance of your Mover® during the

annual inspection of your caravan. If in doubt, please

contact the Truma Services (see Truma Service Booklet or

www.truma.com).

Checks

Check the installation, wiring and connections for damage

at regular intervals. The drive units must be able to move

freely and be returned automatically to the safe idle position

when they are disengaged. If this is not the case, examine

drive units for soiling or corrosion at the guides and clean

if necessary. Undo all moving parts as required and oil or

spray with a lubricant such as WD40 to ensure that the

equipment moves correctly and provides the full range of

movement.

After the annual inspection, check whether all motors react

properly to the buttons on the remote control.

At least every 2 years, an expert must check the Mover®

for rust, check that detachable parts are firmly attached and

check that all safety-related parts are in good working order.

Emergency disengaging function

If the caravan battery has become so discharged that a disen-

gaging cannot be performed using electrical means, or a fault

has occurred, the drive motors can be disengaged manually.

Prise out the plastic cap (m) at the rear

end of the motor using a screwdriver.

Place the socket wrench (size 7 mm –

included in scope of delivery) onto the

hexagon bolt and disengage the drive

unit by turning anticlockwise. Repeat

procedure at the opposite side.

Once the battery has been recharged the rollers can be en-

gaged again electrically.

Trouble-shooting

Check that the batteries in the remote handset are in im-

maculate condition!

Check whether the caravan plug has been plugged into the

safety socket!

Check whether the caravan battery is in immaculate con-

dition and is fully charged! Please note that battery per-

formance can deteriorate considerably at cold ambient

temperatures.

Check whether the flat fuse (20 A) for the engagement mo-

tors is OK. If the fuse is defective, check the engagement

motor connecting cables at the controller for possible short

circuiting!

Perform a reset (approx. 10 seconds – briefly disconnect

battery or disconnect and reconnect safety plug)!

If the fault cannot be remedied, please contact your dealer or

the Truma Service department (see Truma Service Booklet or

www.truma.com).

–

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Truma Mover H TE R Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info