590216

Truma Mover XT 4 Seite 17

17
Zoom out
Zoom in
Vorherige Seite
1/88
Nächste Seite
17
Remote control
Protect the remote control from moisture and direct
sunlight.
1234
a
b
c
h
i
h
i
LED
Figure 2
Switching on the remote control
a = On / Off slide switch
No other remote control function must be active when
the remote control is switched on.
On (LED 4 lights up*)
Off (LED 4 goes off)
* LED 4 flashes for approx. 5 seconds after the remote con-
trol is switched on, until the system is ready for operation.
The following options are available for controlling the caravan:
b using the control knob only
c using the slide control only
b + c using the control knob and the slide control
The caravan symbol on the control knob indicates the current
direction of travel (of the caravan).
The slide control allows the caravan to be moved forwards
and backwards without jerking, with infinitely variable speed
control.
Slide control only
(Forwards, backwards and infinitely variable speed control)
– Push slide control forwards -> caravan moves
forwards (in the direction of the drawbar)
(both wheels rotate forwards)
– Pull slide control backwards-> caravan moves
backwards (in the opposite direction to the drawbar)
(both wheels rotate backwards)
The further the slide control is moved from the zero position,
the faster the speed.
Control knob Mover®XT4
The caravan drawbar can be rotated to the right / left within
a range of approx. 30 cm using the control knob. When the
limit of the rotating range is reached, the rotating procedure is
stopped automatically.
To continue rotating, the caravan must be moved forwards or
backwards in a straight line for a certain distance using the
slide control.
Control knob and slide control Mover®XT4
(Caravan right or left and forwards or backwards)
Operating the control knob and the slide control makes the
Mover®XT4 go round in a circle, whereby the wheels rotate
continuously but the inner wheels rotate more slowly than the
outer wheels.
– Turn control knob to right and push slide control forwards ->
caravan drawbar moves to right
left wheel rotates fast – right wheel rotates slowly forwards
– Turn control knob to left and push slide control forwards ->
caravan drawbar moves to left
left wheel rotates slowly – right wheel rotates fast forwards
– Turn control knob to right and pull slide control backwards ->
caravan drawbar moves to right
left wheel rotates slowly – right wheel rotates fast backwards
– Turn control knob to left and pull slide control backwards ->
caravan drawbar moves to left
left wheel rotates fast – right wheel rotates slowly
backwards
The further the slide control is pushed forwards the end stop,
the faster the speed (freely selectable turning radius and
speed).
Engaging and disengaging
h = Two-handed operation disengagement of drive rollers
(drive rollers swing away from tyres)
i = Two-handed operation engagement of drive rollers
(drive rollers swing towards tyres)
In order to engage and disengage the drive rollers, both
buttons must always be pressed simultaneously – for
approx. 3 seconds (safety delay) – until the engaging or disen-
gaging of the drive rollers commences.
The buttons can be released when the drive rollers are moving
in the direction of the respective end position. The drive rollers
automatically reach their end position.
If the two buttons for disengaging are pressed whilst the
rollers are engaging, engaging is interrupted, the drive roll-
ers are disengaged and automatically move to their end position.
The remote control switches itself off after about 1 minute if
none of the buttons are pressed. The green LED 4 goes out.
To reactivate the remote control, move slide switch to “Off”
and then back to “On” after approximately 1 second.
There is no “On / Off” switch on the caravan itself.
Remote control LED blink code and audio signal
LED 1 red indicates state of charge of caravan battery
good LED off
weak LED on
empty LED on and LED 3 indicates
a fault
LED 2 yellow lights up in the event of a temporary malfunc-
tion, and an acoustic signal is also emitted
in the event of overcurrent / overtemperature
The power is automatically reduced. Allow
system to cool.
flashes if the Mover® is engaged and the
control unit or the remote control has been
switched off.
LED 3 red lights up in the event of a persistent fault, and
an acoustic signal is also emitted
e.g. in the event of a faulty drive motor
apply the parking brake. See “Troubleshooting”
Operating instructions
… 17 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Truma Mover XT 4 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info