629581
10
Zoom out
Zoom in
Vorherige Seite
1/30
Nächste Seite
7
or for Percentage Mode
To change the cylinder size
with the device switched on,
press button „B“ and keep it
pressed until the desired
cylinder size or Percentage
Mode appear in the display.
The measuring time starts af-
ter further 2 seconds. The gas
cylinder content can then be
read off from the display:
For example, for 11 kg con-
tents (gas cylinder full)
or for residual content 2.5 kg
(11 kg gas cylinder only
about 1/4 still filled)
kg
kg
%
The display will switch off
automatically after about
10 seconds.
2
Filling level
as percentage
In Percentage Mode, it is
possible to measure the con-
tents of almost all conven-
tional commercial propane or
butane gas cylinders with fill-
ing weights of up to about
15 kg (which fit on the cylin-
der mount).
By contrast with the standard
measurement in kg, because
of the different cylinder sizes
it is not possible to make re-
course to preset values.
Accordingly, before starting
operation, a basic value of
100 % must be stored in the
memory for the gas cylinder
which is to be measured.
This is done as a rule with the
cylinder completely filled
(filled with butane or propane
depending on the design).
Place the full gas cylinder on
the cylinder mount (make
sure the contact surfaces
are clean!) and secure it as
specified.
Note: To determine a basic
value (100 %), the cylinder
concerned must be more
than half filled, as otherwise
the contents cannot be deter-
mined, and the display will
show:
Percentage
Measurement
To switch the device on, press
button „A“ once, briefly.
The device will carry out a
brief self-test. The measuring
mode set at that particular
time will then be displayed.
The measuring mode can be
changed as appropriate by
pressing button „B“ and kee-
ping it pressed down until the
Percentage display shows:
%
flashing
After a further 2 seconds, the
device will start carrying out
the basic measurement, and
the contents of the gas cylin-
der at that particular moment
will be shown on the display,
flashing, as 100 %.
Now confirm this value
(100 % flashing) by pressing
buttons „A“ and „B“ simulta-
neously, until the display
stops flashing (about
2 seconds).
The device will then carry out
another short measurement,
and the display will show:
After some gas has been
withdrawn, Sonatic will then
show the cylinder content at
%
%
flashing
%
10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Truma Sonatic wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info