Bedienungsanleitung Truma Ultrastore Rapid GE (Seite 8 von 16) (Englisch)

631208

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Manufacturer’s terms of warranty

1. Case of warranty

The manufacturer grants a warranty for malfunctions in the

appliance which are based on material or production faults.

In addition to this, the statutory warranty claims against the

seller remain valid.

A claim under warranty shall not pertain:

for parts subject to wear and in cases of natural wear

and tear,

as a result of using components in the units that are not

original Truma parts and using unsuitable gas pressure

regulators,

as a consequence of failure to respect Truma instructions

for installation and use,

as a consequence of improper handling,

as a consequence of improper transport packing,

use of water not compliant to Drinking Water Directive

98/83/EEC.

2. Scope of warranty

The warranty is valid for malfunctions as stated under

item 1, which occur within 24 months after conclusion of

the purchase agreement between the seller and the final

consumer. The manufacturers will make good such defects

by subsequent fulfilment, i.e. at their discretion either by

repair or replacement. In the event of manufacturers provid-

ing service under warranty, the term of the warranty shall not

re commence a new with regard to the repaired or replaced

parts; rather, the old warranty period shall continue to run.

More extensive claims, in particular claims for compensatory

damages by purchasers or third parties, shall be excluded.

This does not affect the rules of the product liability law.

The manufacturer shall bear the cost of employing the Truma

customer service for the removal of a malfunction under war-

ranty – in particular transportation costs, travelling expenses,

job and material costs, as long as the service is carried out in

Germany. Customer service carried out abroad is not covered

by the warranty.

Additional costs based on complicated removal and installa-

tion conditions of the appliance (e.g. removal of furniture or

parts of the vehicle body) do not come under warranty.

3. Raising the case of warranty

The manufacturer's address is:

Truma Gerätetechnik GmbH & Co. KG,

Wernher-von-Braun Strasse 12,

85640 Putzbrunn (Germany).

In Germany, always notify the Truma Service Centre if prob-

lems are encountered; in other countries the relevant service

partners should be contacted (see Truma Service Booklet or

www.truma.com). Any complaints are to be described in de-

tail. Please also specify the device serial number and date of

purchase.

In order for the manufacturers to be able to determine whether

an incident subject to guarantee has occurred, the end user

must, at his own risk, bring the device to the manufacturers or

send it to them. If there is damage to heaters (heat exchangers),

the gas pressure regulator must also be sent back to the factory.

In instances of the device being sent to the works, dispatch is

to be effected by freight transport. In cases under guarantee,

the works shall bear the transport costs or the costs of deliv-

ery and return. If the damage is deemed not to be a warranty

case, the manufacturer shall notify the customer and shall spec-

ify repair costs which shall not be borne by the manufacturer; in

this case, the customer shall also bear the shipping costs.

–

Declaration of conformity

1. Information about the manufacturer

Name: Truma Gerätetechnik GmbH & Co. KG

Address: Wernher-von-Braun-Str. 12, D-85640 Putzbrunn

2. Device identification

Type / model

LPG-water heater / Boiler Ultrastore Rapid GE (UGE 10)

3. Meets the requirements of the following Directives

3.1 Gas Appliances Directive 90/396/EEC

3.2 Low Voltage Directive 2006/95/EC

3.3 Radio Interference in Vehicles 72/245/EEC

(with the supplements), UN ECE R10

3.4 Electromagnetic Compatibility 2004/108/EC

3.5 End-Of-Life Vehicle Directive 2000/53/EC

3.6 Drinking Water Directive 98/83/EC

and bears the type approval numbers

e1 03 2604, E1 10R–03 2604

and the CE symbol with the CE product ident. no.

CE-0085CL0489.

4. Basis of the conformity assessment

2004/104/EC, 2005/83/EC, EN 89, EN 15033, EN 298 (partly),

DIN EN 60335-1:2010,

IEC 60335-1:2001 mod. +A1:2004 + A2:2006,

DIN EN 60335-2-21:2009,

IEC 60335-2-21:2002 mod. + A1:2004 + A2:2008,

DIN 2001-2, DVGW W270, KTW.

EN 55014-1, CISPR 14-1,

EN 61000-3-2, IEC 61000-3-2,

EN 61000-3-3, IEC 61000-3-3,

ISO 7637 Part 2, ISO 7637 Part 3,

EN 55014-2, CISPR 14-2, EN 13611 Type B,

EN 61000-4-2:2009, IEC 61000-4-2,

EN 61000-4-3, IEC 61000-4-3, EN 61000-4-4, IEC 61000-4-4,

EN 61000-4-5, IEC 61000-4-5, EN 61000-4-6, IEC 61000-4-6,

EN 61000-4-8, IEC 61000-4-8

5. Auditing body

DVGW, Federal Motor Transport Authority

6. Information and the function of the signatory

Signature: Dr. Andreas Schmoll

Managing Director / Engineering Putzbrunn, 10.01.2011

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Truma Ultrastore Rapid GE Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info