Bedienungsanleitung Truma Ultrastore Rapid GE (Seite 11 von 16) (Englisch)

631208

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Cut off the ventilation hose approx. 20 mm below the floor of

the vehicle at an angle of 45° to the direction of travel.

45º

20 mm

Ø 12 mm

Produce connection (22) for cold water supply between

safety/drain valve (14) and elbow (13 – lower pipe) on water

heater.

Route the hot water pipe (23) from the elbow with integrated

breather valve (12 – upper pipe) to the hot water consumers.

Gas connection

The operating pressure for the gas supply is 30 mbar

and must correspond to the operating pressure of the

appliance (see name plate).

The 8 mm gas supply line is connected to the connection noz-

zle (38) with cutting ring connection. The cutting rings are to

be selected according to the gas pipe used (for copper pipe:

support sleeves and brass cutting ring as supplied). Carefully

hold in place with a second wrench when tightening!

Before connecting to the water heater make sure that the gas

lines are free from dirt, chips and such!

Route the pipes in such a way that the appliance can be

removed again for servicing.

In areas frequented by people, keep the number of parting

connections in the gas supply line to an technically feasible

minimum.

The entire system must accord with the technical and

administrative provisions of the individual country of use

(e.g. EN 1949 for vehicles). National specifications and

regulations must be respected.

Flexible water hose routing

As special accessories Truma supplies the water connectors

(12 + 13) and safety/drain (14) valve with a 10 mm diameter

hose nipple (please refer to page 14).

Pressure-resistant (up to 4.5 bar) and hot water-resistant water

hoses in food quality with an internal diameter of 10 mm must

be used.

Route water hoses so that they are as short and free

of kinks as possible. All hose connections must be

secured using hose clamps (also for cold water)! Pressures

of up to 4.5 bar can occur in the safety/drain valve (also with

submergible pumps) because of the heat of the water and the

resulting expansion.

All hot water hoses should be routed in a descending

manner to the safety/drain valve! Otherwise no guaran-

tee of protection from frost!

Installation of the safety (pressure relief)

drain valve

Ø 18 mm

Install the safety/drain valve

(14) at a place which is

easily accessible, near the

water heater. Drill hole with

18 mm diameter and pass

through discharge socket

with hose (15). Fasten safety/

drain valve with 2 screws.

The draining is to be directly

to the outside at a position

protected against splash

water (apply splash guard, if

necessary).

Water pipe routing

Connect cold water supply (16) to safety/drain valve (14).

Direction of flow is unimportant.

Slide elbow fitting (13) onto cold water connecting pipe (lower

pipe) and elbow fitting with integrated ventilating valve (12)

onto hot water connecting pipe (upper pipe) of water heater

as far as it will go. Pull in opposite direction in order to make

sure the elbow fittings are securely attached.

Push the venting hose, external diameter 11 mm (20), onto

the hose grommet of the venting valve (21), and lay it to the

outside without any kinks. Ensure that the bend radius is not

smaller than 40 mm.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Truma Ultrastore Rapid GE Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info