Bedienungsanleitung Truma Ultrastore Rapid GE (Seite 13 von 16) (Englisch)

631208

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Electrical connection 230 V

The 230 V electrical connection must always be made

by an expert (in accordance with VDE 0100, part 721 or

IEC 60364-7-721, for example, in Germany). The information

given here is not intended as instructions for you to carry out.

It is for assisting the expert assigned to carry out the job, act-

ing as auxiliary information when connecting the appliance!

The connection to the power supply is by means of a cable

(e.g. flexible sheathed cable H05VV-F) to the 230 V supply

line (3 x 1.5 mm²) and a cable to the 230 V control panel

(4 x 1.5 mm²).

Always pay attention to connect carefully with the correct col-

ours and numbers!

For maintenance and repair work a disconnecting device must

be provided on the vehicle for all-pole disconnection from the

power supply, with at least 3.5 mm contact clearance.

All cables must be secured with cable clips. The cables

from the heating element can be tightened to the sup-

port column on the side of the Ultrastore by means of clamp-

ing to the eye provided with a cable binder. Attaching water

containers or pipes to the eye is not allowed.

Connection 230 V control panel

Connect control panel cable, 230 V cable and heating element

cable as shown in the drawing.

Cables must be in accordance with the technical rules and

regulations of the country in which the vehicle is to be

registered, for the first time.

230 V ~

control panel

supply line 230 V ~

3 x 1.5 mm²

Ultrastore

heating

element

1300 W

850 W

yellow/green

blue

brown

450 W

850 W

– 3 –

CPC CPC

yellow/green

– 2 –

CPC

– 1 –

4 x 1.5 mm²

Correct connection of L and N line to the corresponding power

supply lines must be ensured for safe operation.

Function check

After installation, the gas feed line must be tested for tight-

ness by the pressure-drop method. A test certificate is to be

issued.

Correct operation of 230 V heating elements must be checked

by doing a power or current consumption measurement in

switch position 850 W and 1300 W.

Position 850 W 3 – 4 A 750 – 900 W

Position 1300 W 5 – 6.5 A 1150 – 1400 W

If measured values are not within this range, please double

check correct connection of the heating elements.

Then check all functions of the appliance, as specified in the

operating instructions, in particular the water content draining

function. There shall be no claims under guarantee for

damage caused by frost!

Never operate the water heater without water contents.

It is, however, possible to briefly check the electrical function

without water contents. Always observe the operating instruc-

tions prior to operation!

The operating instructions and completed guarantee card are

to be given to the owner of the vehicle.

Warning information

The installer or vehicle owner must apply the yellow sticker

with the warning information, which is enclosed with the

appliance, to a place in the vehicle where it is clearly visible to

all users (e.g. on the wardrobe door)! Ask Truma to send you

stickers, if necessary.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Truma Ultrastore Rapid GE Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info