Bedienungsanleitung Trumatic Combi 6 E (Seite 15 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch)

484618

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Room thermostat

To measure the room temperature, an external room tempera-

ture sensor (s) is located in the vehicle. The location of the

sensor is determined individually by the vehicle manufacturer,

depending on the vehicle type; consult the operating instruc-

tions for your vehicle for further details.

s = Room temperature sensor

The thermostat setting on the control panel (1 – 5) must be

determined individually depending on the heating requirement

and the type of vehicle. For an average room temperature of

about 23 °C, we recommend a thermostat setting of about 4.

FrostControl

(safety/drain valve)

FrostControl is a currentless safety/drain valve. When there

is a danger of frost, it automatically drains the contents of

the boiler through a drainage muff. If excessive pressure is

present in the system, pressure will be automatically intermit-

tently equalized through the pressure relief valve.

t = rotary switch position “Operation”

u = push button position “Closed”

w = push button position “Drain”

x = drainage muff (led outside through floor of vehicle)

Closing the drain valve

Check if the rotary switch is set to “Operation” (position t),

meaning that it is parallel to the water connection and

engaged.

Close the drain valve by activating the push button. The push

button must engage in position (u) “closed”.

Only when the temperature around the drain valve is over

around 7 °C can it to be closed manually with the press button

(“u” position) and the boiler filled.

Truma supplies a heating element (part no. 70070-01) as an

accessory, which is inserted into the FrostControl and fixed in

place with a retaining bracket. This heating element heats the

FrostControl to approx. 10 °C when the Combi is switched on.

This means that the boiler can be filled after a shorter time, ir-

respective of the temperature in the installation compartment.

Automatic opening of the drain valve

If the temperature around the drain valve is below about 3 °C,

it will open automatically and the push button will disengage

(outward movement) (“w” position). The water from the boiler

will be released through the drainage muff (x).

Manual opening of the drain valve

Turn the rotary switch by 180° until it engages, whereby the

push button moves out (position w). The water in the boiler

drains out through the drainage muff (x).

The FrostControl drainage muff (x) must be free of contamina-

tion (slush, ice, leaves, etc.) at all times so the water can drain

out easily! There shall be no claims under guarantee for

damage caused by frost!

Taking into operation

Heating is possible without restrictions with gas,

electrical and mixed operation, with or without

water.

Check to make sure the cowl is unobstructed. Be sure to

remove any covers that may be present.

Turn on gas cylinder and open quick-acting valve in the gas

supply line.

Check whether the power supply fuse protection on the camp

site is adequate for the 900 W (3.9 A) or 1800 W (7.8 A) that

have been selected using the power selector switch.

The cable drum must be fully unwound in order to prevent the

power cable from overheating.

Summer operation

(boiler operation only)

Select gas or electrical operation using the power selector

switch. Illumination of the yellow LED (g) on the power

selector switch indicates that the unit is operating with 230 V.

Mixed operation (gas and electrical) is not possible in

summer mode. With this setting the unit automatically

selects electrical operation with a preselected power setting of

900 W or 1800 W.

Move the rotary switch on the control panel to position (I –

summer operation) 40 °C or 60 °C. The green (k) and yellow

(p) LEDs light up.

When the selected water temperature is reached (40 °C or

60 °C) the heater shuts off and the yellow LED (p) goes off.

Winter operation

Heating with water temperature monitoring

Select gas, electrical or mixed operation using the power

switch. Illumination of the yellow LED (g) on the power se-

lector switch indicates that the unit is operating with 230 V.

Move rotary switch on control panel to operating position (n).

Set the rotary switch (h) to the desired thermostat setting

(1 – 5). The green LED (k) for operation is lit and simulta-

neously indicates the position of the selected room tem-

perature. The yellow LED (p) indicates the water‘s heat-up

phase.

The device automatically selects the required power setting

in accordance with the temperature difference between the

temperature selected on the control panel and the current

room temperature. When the room temperature selected on

the control panel is reached, the heater switches back to the

smallest setting and heats the water to 60 °C. Once the wa-

ter temperature is reached, the heater switches off and the

yellow LED (p) goes out.

–

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trumatic Combi 6 E Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info