Bedienungsanleitung Trumatic Combi 6 E (Seite 16 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch)

484618

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Gas operation fault

If a fault occurs during gas operation the red LED (r) on the

control panel illuminates.

Please consult the Trouble-Shooting list for possible causes.

A reset (fault reset) is carried out by switching off, waiting

until all LED’s on the control panel have stopped flashing, and

then switching the heater on again.

If a window to which a window switch has been fitted is

opened, the heater stops operating and the red LED (r)

flashes. The heater continues operating when the window is

closed.

Electrical operation fault

If a fault occurs during electrical operation the yellow indicator

lamp (g) on the power selector switch goes off.

Possible causes can be found in the troubleshooting list.

If the 230 V power supply is interrupted for just a brief

period of approximately 1 second during operation, the

heater will subsequently resume as normal.

Filling the water heater

Check if the rotary switch for the drain valve (FrostControl) is

set to “Operation”, meaning that it is parallel to the water

connection and engaged.

Close the drain valve by pushing the push button until it

engages.

When the temperature at FrostControl is below about

7 °C, first switch on the heater to warm the installation

compartment and FrostControl. After several minutes, when

the temperature at FrostControl is above 7 °C, the drain valve

can be closed.

Switch on power for water pump (main or pump switch).

Open hot water taps in kitchen and bathroom, (set preselect-

ing mixing taps or single-lever fittings to “hot”). Leave the fit-

tings open for as long as it takes for the boiler to displace the

air and fill up, and the water to flow without interruption.

If just the cold water system is being operated, without

using the water heater, the heater tank also fills up with

water. To avoid frost damage, the boiler must be drained

through the drain valve, even if it was not operated.

When connecting to a central water supply (rural or city

mains), a pressure reduction valve must always be in-

stalled to prevent pressures above 2.8 bar from developing in

the water heater.

Draining the water heater

Switch off power to water pump (main or pump switch).

Open hot water taps in kitchen and bathroom.

In order to check the water that is flowing out, place an

appropriate container (capacity 10 litres) beneath the drain

valve (FrostControl) drainage muff (x).

Turn the rotary switch on the drain valve by 180° until it

engages, whereby the push button moves out and the drain

valve opens.

Check whether all of the water in the boiler (10 litres) has

been drained into the container via the drain valve.

There shall be no claims under guarantee for damage

caused by frost!

Heating without water temperature monitoring

Select gas, electrical or mixed operation using the power

switch. Illumination of the yellow LED (g) on the power

selector switch indicates that the unit is operating with 230 V.

Move rotary switch on control panel to operating position (m).

Turn the rotary switch (h) to the desired thermostat setting

(1 – 5). The green LED (k) for operation is lit and simultane-

ously indicates the position of the selected room tempera-

ture. The yellow LED (p – water‘s heat-up phase) will be lit

only when the water temperature is below 5 °C!

The device automatically selects the required power setting

in accordance with the temperature difference between the

temperature selected on the control panel and the current

room temperature. Once the room temperature selected on

the control panel has been reached, the heater switches off.

The warm air fan continues to run at slow speed until the out-

going air temperature (on the unit) has fallen to 40 °C or less.

If the boiler is filled, the water will automatically be heated

at the same time. The water temperature is then dependent

on the heating output being given off, and the duration of

heating required to reach the desired room temperature.

Heating with drained water system

Select gas or electrical operation using the power selector

switch. Illumination of the yellow LED (g) on the power

selector switch indicates that the unit is operating with 230 V.

Move rotary switch on control panel to operating position (m).

Turn the rotary switch (h) to the desired thermostat setting

(1 – 5). The green LED (k) for operation is lit and simultaneously

indicates the position of the selected room temperature. The

yellow LED (p) will be lit only when the temperature of the

unit is below 5 °C!

Depending on the operating mode, the unit will automatical-

ly select the required power level according to the tempera-

ture difference between the setting on the control panel and

the current room temperature. Once the room temperature

selected on the control panel has been reached, the heater

switches off. The warm air fan continues to run at slow

speed until the outgoing air temperature (on the unit) has

fallen to 40 °C or less.

Switching off

Switch off heater at control panel using rotary switch (position o).

The green LED (k) goes off.

If the green LED (k) blinks after switching off, then the

unit‘s after-running is active in order to reduce the unit‘s

temperature. This will end after a few minutes and the green

LED (k) will go off.

Always drain water contents if there is a risk of frost!

If the appliance is not to be used for a prolonged period, close

the quick-acting valve in the gas supply line and turn off the

gas cylinder.

–

Trumatic Combi 6 E Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info