Bedienungsanleitung Trumatic E 2400 (Seite 15 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch)

484023

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

Trumatic E 2400

Symbols used

Symbol indicates a possible hazard.

Comment including information and tips.

Safety instructions

The use of upright gas cylinders from which gas is taken in

the gas phase is mandatory for the operation of gas regula-

tors, gas equipment and gas systems. Gas cylinders from

which gas is taken in the liquid phase (e.g. for fork lifts) must

not be used, since they would result in damage to the gas

system.

If the gas system is leaking or if there is a smell of gas:

extinguish all naked flames

do not smoke

switch off the appliances

shut off the gas cylinder

open windows and door

do not actuate any electrical switches

have the entire system checked by an expert!

Repairs may only be carried out by an expert!

A new O-ring must always be installed after dismantling the

exhaust duct!

Guarantee claims, warranty claims and acceptance of liability

will be ruled out in the event of the following:

modifications to the unit (including accessories),

modifications to the exhaust duct and the cowl,

failure to use original Truma parts as replacement parts and

accessories,

failure to follow the installation and operating instructions.

It also becomes illegal to use the appliance, and in some

countries this even makes it illegal to use the vehicle.

The gas supply’s operating pressure (30 mbar) must be the

same as the unit’s operating pressure (see type plate).

Liquid gas systems must comply with the technical and

administrative regulations of the respective country of use

(e.g. EN 1949 for vehicles or EN ISO 10239 for boats in

Europe). National directives and regulations (e.g. DVGW

worksheet G 607 for vehicles and G 608 for boats in Germany)

must be complied with.

For vehicles for commercial use, the relevant accident preven-

tion regulations issued by the professional associations are to

be respected (BGV D 34).

The inspection of the gas system is to be repeated every

two years by an approved liquid gas specialist (DVFG, TÜV,

DEKRA). This is to be confirmed on the corresponding inspec-

tion certificate (G 607, G 608, or BGG 935).

The vehicle owner is always responsible for arranging the

inspection.

Pressure regulating equipment and hoses must be replaced

with new ones no more than 10 years after the date of

manufacture (every 8 years if used commercially). This is the

responsibility of the operator.

Liquid gas equipment must not be used when refuelling, in

multi-storey car parks, in garages or on ferries.

–

Table of contents

Symbols used ...................................................................... 15

Safety instructions .......................................................... 15

Important operating notes ............................................. 16

Operating instructions

Control panel with sliding switch ....................................... 17

Control panel with rotary switch ......................................... 17

Switching on the Heating ................................................... 17

Switching on the Ventilation ............................................... 17

Switching off ....................................................................... 17

Green LED “Operating” ...................................................... 17

Fuses ................................................................................... 17

Red LED “Failure” ............................................................... 17

Disposal ............................................................................. 17

Accessories ....................................................................... 18

Technical data ................................................................... 18

Trouble-shooting list ........................................................ 19

Declaration of conformity .............................................. 20

Manufacturer’s terms of warranty ................................ 20

Installation instructions

Intended use ........................................................................ 21

Approval .............................................................................. 21

Regulations .......................................................................... 21

Notes on the installation in commercial vehicles .............. 21

Notes on installation in driver's cab .................................... 21

Notes on installation in boats .............................................. 21

Choice of location ............................................................ 21

Exhaust duct ..................................................................... 22

Permissible duct lengths ..................................................... 22

Interior installation using the wall cowl kit ............... 22

Assembly of wall cowl ........................................................ 22

Fastening the appliance ...................................................... 22

Double cowl duct connection to the heating

appliance ........................................................................... 23

Under-floor assembly with wall cowl kit ..................... 23

Fastening the appliance ...................................................... 23

Warm air distribution and circulating air return with

interior installation ........................................................... 23

Warm air distribution .......................................................... 23

Circulating air return ............................................................ 23

Warm air supply and circulating air return with

outside assembly ............................................................. 23

Connection of the ducts to the appliance ........................... 24

Assembly of the ducts at leadthroughs .............................. 24

Warm air distribution .......................................................... 24

Circulating air return ............................................................ 24

Fitting the control panel ................................................. 24

Installing the control panel with rotary switch ................... 24

Installing the control panel with slide switch ..................... 25

Fitting the electronic control unit ................................. 25

Electrical connection 12 V / 24 V .................................. 25

Gas connection ................................................................. 25

Function check ................................................................. 25

Warning information ....................................................... 25

Trumatic E 2400 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info