Bedienungsanleitung Trumatic E 2400 (Seite 17 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch)

484023

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

Always observe the opera ting instructions and “Impor-

tant operating notes” prior to starting! The vehicle owner

is responsible for the correct operation of the appliance!

The installer or vehicle owner must apply the yellow sticker

with the warning information, which is enclosed with the ap-

pliance, to a place in the vehicle where it is clearly visible to

all users (e.g. on the wardrobe door)! Ask Truma to send you

stickers, if necessary.

Control panel with sliding switch

a = Slide valve

Heating – Off – Ventilation

b = Slide valve for

high setting (large flame symbol)

low setting (small flame symbol)

Control panel with rotary switch

Trumatic E

c = “Heating” rotary switch

high setting (large flame symbol)

low setting (small flame symbol)

d = “Off” rotary switch

e = “Ventilation” rotary switch

high setting (large symbol)

low setting (small symbol)

Switching on the Heating

Remove cowl cap.

Turn on gas cylinder and open quick-acting valve in the gas

supply line.

Adjust desired room temperature at rotary knob.

Switching the heating on:

Control panel with sliding switch

Set the switch (a) to Heating and switch (b) to the desired

output setting.

Control panel with rotary switch

Set the rotary switch to the desired output setting (c).

If the outside temperature is low, switch to high setting.

The Trumatic E heater has been tested and approved for

operation, also when the vehicle is moving. The burner

with fan assistance guarantees satisfactory operation, even

under extremely windy conditions. It may be necessary to ob-

serve respective, country-specific regulations for the operation

of liquid gas appliances when the vehicle is moving.

–

Switching on the Ventilation

Control panel with sliding switch

Set switch (a) to Ventilation and switch (b) to the desired out-

put setting.

Control panel with rotary switch

Set the rotary switch to the desired output setting (e).

Switching off

Set the sliding switch (a) or the rotary switch (d) to the centre.

If the appliance is switched off after a heating phase, the fan

can continue running in order to make use of the residual heat.

If the appliance is not used for a prolonged period of time,

close quick-acting valve in the gas supply line and turn off gas

cylinder.

Green LED “Operating”

(under rotary control knob)

When the device is switched on (heating or ventilation), the

green LED must light up (the fan is operational). If the LED

does not shine, check the (main) switch. For this purpose

observe respective instructions of the vehicle manufacturer.

During the heating process whilst the flame is burning, the

green LED shines twice as brightly. This also makes it possible

to determine the instantaneous switching point of the room

temperature.

Fuses

The device and control panel fuses are on the electronic con-

trol unit on the device.

Device fuse (F1):

3.15 AT – slow – (EN 60127-2-3)

Control panel fuse (F3):

1.6 AT – slow –

The fine-wire fuse must only be replaced by a fuse of the

same design.

Red LED “Failure”

In the event of a failure, the red LED shines. Possible causes

for the failure can be e.g. no gas, insufficient combustion air,

heavily soiled rotor, defective fuse etc.. Deactivate by switch-

ing off and then switching on again.

Opening a window to which a window switch is

attached and closing it again is the equivalent of switch-

ing the equipment off and on again at the control panel

(e.g. a fault reset)!

Flash operation indicates that the operating voltage is too

low or too high for the appliance (charge battery, if necessary).

In Germany, always notify the Truma Service Centre if prob-

lems are encountered; in other countries the relevant service

partners should be contacted (see Truma Service Booklet or

www.truma.com).

Disposal

The device must be disposed of in line with the administra-

tive regulations of the respective country in which it is used.

National regulations and laws (in Germany, for example, the

End-of-life Vehicle Regulation) must be observed.

Operating instructions

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trumatic E 2400 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info