Bedienungsanleitung TTulpe Indoor B-10 B30 Eco (Seite 9 von 12) (Englisch)

782471

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Function

The water heater is used to produce instant hot water. The

removal of hot water can be performed by multiple taps.

By turning on the relative tap, the main burner switches on heating

the water that passes.

1.After adjusting the temperature, the traditional knob control gas

water heater cannot keep the setting temperature constant due to

the fluctuation of water pressure and air pressure.

Due to its digital control valve and more advanced control system,

the controller can control the opening of the proportional valve ac

cording to the increase or decrease of the water temperature dete

cted by the temperature sensor , in case of water pressure or air

pressure fluctuation, so as to control the gas flow rate. Therefore,

the hot water outlet temperature can keep the setting

temperature constant.

2.The traditional knob control gas water heater will have high CO

rate under high pressure due to the unstable air pressure

supplied.

However, for this type of gas water heater with constant

temperature function, because the gas valve has a pressure

stabilizing fun ction, when the gas pressure is too high, the valve

will keep the pr essure at the outlet of the valve stable, then the

CO rate can be c ontrolled in a low range.

Usage

Ensure that the gas tap and all water taps are switched off

Turn on the Main gas supply tap or that of the gas tank if using

Liquefied Petroleum Gas (L.P.G.)

Open the gas tap,not supplied with the device,placed immediat

ely before the water heater on the gas input pipe

Press ON/OFFbutton,the gas water heater will be in standby s

tatus.Press UP or DOWN button to set the temperature of wate

r outlet (Fig 7). Press UP or DOWN button for one time，then t

he setting temperature will increase or decrease 1℃accordingl

y.When long press UP or DOWN button for every 0.3 seconds,

the setting temperature will increase or decrease 1℃.Tempera

ture setting range can be 35-60℃

When the gas water heater is connected with water supply,the

ignition pin will start to work and ignite the main burner.

If disconnect the water supply (turn off the water tap)or press

ON/OFFbutton to turn off the gas water heater,the burner will

automatically shut down.Then the device awaits another heat

ing request.

If after 60 seconds it does not switch on, the controller detector

interrupts the flow of gas and blocks the device.

To reuse the device after it has been blocked, close the hot

water extraction tap and then reopen it to restart the sequence.

If the main burner accidentally switches off, the device will

attempt to turn it on again.

If within 60 seconds the device does not function it is blocked .

The device is built to function with normal water pressure; in add

ition, a temperature selector B is also supplied.

Rotate the knob completely to the left to obtain the minimum

water output or completely to the right for the maximum water

output.

When the water heater is not used for long periods close the

gas supply tap or the LPG gas valve on the tank.

For the best operational results, it is recommended to have

aqualified technician service the machine at least once a year.

DANGER OF FREEZING

If there is a possibility that the area where the device is stalled

could reach below 0°C, the device must be emptied of all water

contain ed. In case of freezing conditions disconnect the

incoming water pipe to drain the water heatercompletely.

MAINTENANCE

To maintain the machine at maximum efficiency, have qualified

personnel perform a maintenance check at least once a year.

Before cleaning or performing maintenance,

opening or disassembling the panels, switch off the device and

turn off the gas supply. Check the main burner and the pilot

flame, the ignition electrode, the safety valve and that there is

no leakage.

Check that there is nothing obstructing the passages within the

exchanger smoke channel.

To clean the outside of the panels, utilize a cloth with soap and

water.

Do not use solvents, powders, or abrasive sponges.

Do not clean the device and/orits parts with flammable material

s (e.g. petrol, alcohol, diesel etc.).

Troubleshooting: problems and solutions

Fault code

It will immediately shut down all gas channels

and display the fault code on the screen whe

n the controller detects a fault.

Fault Code meaning

E1：Ignition failure (Including ignition failure caused by low voltage).

E2：Ignition failure for the second time. (Including ignition failure

caused by low voltage).

E3：MCU self-check fault or EEPROM fault or wires fault.

E4：Temperature sensor of water outlet has open circuit or short

circuit.

E5：Temperature sensor of water inlet has open circuit or short

circuit（When the temperature sensor of water inlet is include d）.

E6：False fire.

E7：The overheating thermostat has open circuit.

E8： Temperature of water outlet is over

℃

E9：Continuously working time（When this function is available）.

Fault Code Solution

1. When the display appears the fault code except for E7, after

solving the problems, there are two methods to remove the fault

co de。

①Press ON/ OFF button to restart for two times, then fault code

can be removed

②Remove and install the battery or turn off and open the water

tap.

2. When the display appears the fault code E7,or the display appe

ars other fault codes for 5 times in 15 minutes, display appear fa

ult code and “nL ,”the only solution is to press DOWN button for

more than 5 seconds. Then the fault code can be removed。

148.00 mm

210.00 mm

TTulpe Indoor B-10 B30 Eco Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von TTulpe Indoor B-10 B30 Eco

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info