Bedienungsanleitung Tunturi Classic loopband RUN 3.0 (Seite 9 von 84) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch, Finnisch)

542653

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

8 9

Run 3.0 - OWNER’S MANUAL ENGLISH

ALIGN THE BELT ACCORDING TO THE FOLLOWING

INSTRUCTIONS:

1. Turn the power switch on and increase the treadmill’s

speed to 5 km/h (3 mph).

2. If the belt drifts to the left, turn the left adjustment bolt

1/4 turn clockwise and the right adjustment bolt 1/8 turn

anti-clockwise. If the belt drifts to the right, turn the right

adjustment bolt 1/4 turn clockwise and the left adjustment

bolt ¼ turn anti-clockwise.

3. If the belt remains centered the adjustment is correct.

If not, continue to make small adjustments as above

until the belt is correctly aligned. If the belt is allowed run

across to one side for long periods of time the edges of

the belt may be damaged and the treadmill may not

continue to operate correctly. Any damage to the belt

caused by the lack of necessary adjustment will not be

covered by the warranty.

ADJUSTING THE BELT TENSION

The belt must be tensioned if it begins to slip on the rollers.

In normal use, however, keep the belt as loose as possible!

The belt tension is adjusted by turning the same screws

as used for aligning the running belt. If turning the screws

will not effect the belt tension, please contact your local

Tunturi dealer.

1. Increase the treadmill’s speed to 5 km/h (3 mph).

2. Turn both adjustment screws an equal amount, ¼ turn

clockwise.

3. Try to slow the belt down by holding onto the handrails

and braking as you walk (as if you were walking downhill).

If the belt slips, turn another 1/4 turn and repeat the test.

When braking heavily the belt may slip. If the belt keeps

slipping despite repeated adjustments, please contact

your local Tunturi dealer.

MALFUNCTIONS

NOTE! Despite continuous quality control, defects

and malfunctions caused by individual components may

occur in the equipment. In most cases it’s unnecessary to

take the whole device in for repair, as it’s usually sufcient

to replace the defective part. Always give the model,

serial number of your equipment and in case of

malfunctions also conditions of use, nature of malfunction

and any error code.

When you encounter unusual behavior from the treadmill,

simply turn the power switch off, wait 1 minute and turn

the power switch on to reset the treadmill. This should

clear incidental errors and ready the treadmill for normal

operation again. If after you have reset the treadmill

by turning the power switch off and on again, and the

treadmill is still not operational, contact your local Tunturi

dealer for service.

If you require spare parts, always give the model, serial

number of your equipment and the spare part number for

the part you need. The spare part list is at the back of this

manual. Use only spare parts mentioned in the spare part

list.

ERROR CODES

The user interface will display information about

operational faults.

E1: Speed sensor error. Unplug the electrical cord from

the wall outlet and from the treadmill, wait 1 minute and

turn the power switch on again. If treadmill recovers to

normal operation, you may continue to use the treadmill.

Otherwise, call the dealer for service.

E3: Lift motor error. Unplug the electrical cord from the

wall outlet and from the treadmill, wait 1 minute and

turn the power switch on again. If treadmill recovers to

normal operation, you may continue to use the treadmill.

Otherwise, call the dealer for service.

MOVING AND

STORAGE

After assembly is complete, you may fold the machine

into the upright position for storage. To hold the machine,

raise the desk until it locks in to position.

NOTE! Make sure you hear the click sound of the

deck locking into position. This is to ensure the deck is

locked in place and will not drop back down.

NOTE! Make sure the treadmill’s elevation is at 0

before folding the deck. If the elevation is not at 0, folding

will damage the mechanism.

120918_RUN 3.0_manual.indd 9 9/20/2012 5:09:40 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tunturi Classic loopband RUN 3.0 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info