Bedienungsanleitung Turbionaire Smart 14eco (Seite 10 von 126) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

804594

Zoom out

Zoom in

Vorherige Seite

1/126

Nächste Seite

c. Before proceeding, make sure that:

d. Mechanical handling equipment is available if it is necessary for the handling of

coolant cylinders;

e. All individual protection equipment are available and correctly used;

f. the recovery process is permanently supervised by a qualified person;

g. The recovery equipment and cylinders are in accordance with the appropriate

standards.

h. If possible, drain the cooling system.

i. If aspiration is not possible, use a collector so that the refrigerant can be removed from

different parts of the system.

j. Ensure that the cylinder is in upright position before recovery.

k. Start the recovery machine and use it in accordance with the instructions of the

manufacturer.

l. Do not fill the cylinders. (Must not exceed 80% of the quantity of liquid).

m. Do not exceed the maximum working pressure of the cylinder, even temporarily.

n. When the cylinders have been correctly loaded and the process has been completed,

make sure that the cylinders and the equipment are quickly removed from the working area

and that all the insulation valves of the equipment are closed.

o. The recovered refrigerant must not be loaded into another cooling system unless it has

been cleaned and checked.

17. Labelling

The equipment must be labelled with the mention that it has been dismantled and emptied

by the refrigerant. The label must be dated and signed. Ensure that there are labels on the

equipment showing that the equipment contains flammable refrigerant.

18. Recovery

When performing the procedure of removing the refrigerant from a system, either for

service or for decommissioning, it is recommended that all refrigerants are safely removed.

When transferring the refrigerant to cylinders, make sure that only the recovery cylinders

are used for the refrigerant. Ensure that the correct number of cylinders is available to take

up the total quantity of the refrigerant in the system. All cylinders to be used are intended

for the recovered refrigerant and labelled for the respective refrigerant (i.e. special

cylinders for the recovery of the refrigerant). The cylinders must be equipped with the

pressure valve and the associated shut-off valves in good working order. Drained recovery

cylinders are evacuated and, if possible, cooled before recovery.

The recovery equipment must be in good working order, provided with a set of available

equipment instructions and be suitable for the recovery procedure of flammable

refrigerants. In addition, a set of calibrated scales must also be available in good working

order. Hoses must be equipped with connection mechanisms without leakage and in good

condition. Before using the recovery machine, make sure it is in good working condition,

that it was properly maintained and that all associated electrical components are sealed to

prevent ignition when a coolant is released. Consult the manufacturer if in doubt. The

recovered refrigerant will be accordingly returned to the supplier of the refrigerant in the

recovery cylinder and the note referring to the transfer of waste will be prepared. Do not

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Turbionaire Smart 14eco Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info