Bedienungsanleitung Uniprodo Uni Cooler 02 (Seite 7 von 39) (Alle Sprachen)

778966

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

• In the UNI_COOLER_01 model, the function is

activated manually using the button (2), however, it

will work only when the device is switched on (the

On / O button (1) is on – the diode A1 lights up).

There is only one stage of heating setpoint. If heating

was started manually, it can be operated using the (H)

button on the remote control or on the control panel.

Note: Always set the switch (2) to the O position,

if we turn o the whole device (despite turning

o the device with the remote control, the user

must approach it and turn o the heating function

manually).

• The UNI_COOLER_03 model has an automatic

activation of the heating function from the level of

the control panel or the wireless remote control. The

heating function has the option of the two-stage

selection of the heating power (change of the stage

by pressing the button (H)). You can disable the

option by pressing the (H) button on the panel or on

the wireless remote control.

Cooling function

• All models of the devices have the air cooling function.

• The max. cooling temperature is about 3-5 °C (only

with air humidity <40%). Attention: If the device is

being used in conditions with high temperatures and

humidity of >40%, the device will not be able to lower

the air temperature.

• In order to activate the function, the tank of the device

must be lled with water and previously frozen cooling

cartridges or ice cubes. It is forbidden to activate the

function without the tank lled with water.

• Topping up the water tank:

In the UNI_COOLER_03, UNI_COOLER_01 and UNI_

COOLER_02 models, it is necessary to pull out the water

tank and ll it with water and frozen cooling cartridges

or ice cubes – this is shown in the picture below:

• In the UNI_COOLER_04 model, the water tank is

topped up by pouring clean water and dropping ice

cubes through the inlet hole (7). Note: It is forbidden

to use cooling cartridges in this model! Observe

the level of water being poured on the water level

indicator (4).

• Regularly observe the water level in the tank in the

course of the device operation. If necessary, ll up the

water shortages.

911

EN 12

H. Button for switching on the heating function

H1. – low heating power (UNI_COOLER_03 model)

H2. – high heating power (UNI_COOLER_03 model)

H3. – heating enabled (Model UNI_COOLER_01)

The elements marked with the numbering A1 – H3 are

diodes informing about the activation of a given device

function. If the function is active, the diode lights up,

otherwise it is o.

Heating function

• The UNI_COOLER_01 AND UNI_COOLER_03 models

have the air heating function.

Setting the operation time

The operating time of the device is set by single pressing the

button (E). Each pressing causes to add 1h starting from 1 to

12h (in the case of the UNI_COOLER_04 model, addition of

0.5h starting from 0.5 to 7.5h).

Operation

• Connect the device to the power supply source.

• Switch on the device with the On / O button (A).

• Set the device operation manner according to own

preferences. The number of available options from

among the operating modes depends on the device

model.

• Single pressings of the option data buttons cause their

activation, the next pressings in case of the buttons

with the single selection causes deactivation of the

given option. In the case of buttons with possibilities

of selection of the functioning option, single pressings

will cause jumping between subsequent options, after

reviewing all options, the next pressing will cause

deactivation of the option.

Depending on the device model, the following options are

available:

1. COOL/ COOL AIR– cooling option

2. TIMER – minute timer

3. MODE – selection of the ventilation mode

4. SWING – switching on / o the jalousie movement

5. SPEED – ventilation speed regulation

6. WARM – heating option

7. IONIZER – switching on / o the ionization function

• The user has the possibility to manually set the

ventilation angle (manually setting horizontal

jalousies).

• In case of operating the device with a remote control,

it is necessary to direct the remote control transmitter

towards the device.

• Always turn o the device after the end of its use.

It is best to disconnect the device from the power

supply source.

• In case of moving the device to another location, it

is necessary to use the handles if they are installed

in the device and the wheels. The water tank must

be emptied for the period of transport. Transport the

device only and exclusively in the vertical position.

4.4 CLEANING AND MAINTENANCE

• Before cleaning, maintenance and when not in use,

make sure the power cable is disconnected and the

device has cooled down.

• Use cleaners without corrosive substances to clean

each surface.

• Clean the device with a soft cloth. It is forbidden to

pour water on the device.

• Regularly clean the lters installed in the device.

Cleaning the external and internal lter:

Dismantle the external lter by unscrewing it from the back

part of the device housing. Dismantling the external lter

(11) will enable access to the internal lter with a honey

comb structure (9).

21.02.2022

13 EN

Clean the lters with water with addition of a mild detergent.

If required the external lter can be soaked in water for

approx. 10 minutes and then it is necessary to remove

the dirt with a soft brush. Before retting the lter, dry it

completely! Place the cleaned lters back in the device,

screw on.

• Cleaning the water tank:

In case of models UNI_COOLER_03, UNI_COOLER_01 and

UNI_COOLER_02, it is necessary to drain water from the tank,

then pull it out and clean it with a mild agent. In the case

of the UNI_COOLER_04 model, in order to clean the tank, it

is necessary to disassemble the lters at rst and thus get

access to the tank. Drain the dirty water through the water

outlet.

• Store the unit in a dry, cool place, free from moisture

and direct exposure to sunlight.

SAFE REMOVAL OF BATTERIES AND RECHARGEABLE

BATTERIES

The remote control connected to the device is battery-

powered. Worn batteries must be removed from the

device proceeding analogously to their installation. Recycle

batteries.

DISPOSING OF USED DEVICES

Do not dispose of this device to municipal waste systems.

Hand it over to electric and electrical device recycling and

collection point. Check the symbol on the product, user

manual and packaging. The plastics used to construct the

device can be recycled in accordance with their markings. By

recycling, you are making a signicant contribution to the

protection of our environment. Contact local authorities for

information on your local recycling facility.

Uniprodo Uni Cooler 02 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info