557924

UPM WT440H Seite 2

2
Zoom out
Zoom in
Vorherige Seite
1/6
Nächste Seite
MOONPHA SE
MONDAY
CLOCK1
OUT
IN
TREND
TREND
1
1
1
1
1
2
2
2
3
3
*
*
4
4
2
3
4
SETTING UP THE RECEIVER
WIRELESS TRANSMISSION
WIRELESS TRANSMISSION
Automatic Learn Function:
Manual Learn Function (Remote Signal Search):
The learn function executes automatically and runs for approximately
3 minutes when batteries are first installed in the receiver.
Press and hold for 3 seconds to start.CHN
If a new remote transmitter is added or if signal is lost (outdoor
readout on the receiver is blinking), the learn function must be
executed again.
Within these 3 minutes, the receiver will pick up the temperature and
humidity signals from remote transmitter and display the reading.
Unit will beep to indicate that the learn function has started.
Channel symbol will blink and unit will continue to beep as each
remote transmitter is detected.
Within 3 minutes, the temperature and humidity reading of the remote
transmitter will display on the receiver.
TEMPERATURE ALARM TEMPERATURE ALARM
MOONPHASE
MONDAY
CLOCK1
OUT
IN
TREND
TREND
MOONPHA SE
MONDAY
CLOCK1
OUT
IN
TREND
TREND
2
Synchronized
Remove battery cover
batteries into compartment,
observing proper polarity; then
replace cover
Insert
1
2
3
2 AA size batteries (included)
3
3
1
1
4
4
2
2
*
*
3
3
2
1
WIRELESS TRANSMISSION
For optimal performance:
Place the receiver and remote transmitter side by side about 1 metre
apart, and allow the receiver and remote transmitter to synchronize
for 10 minutes before you place the remote transmitter outdoors.
Environmental factors and signals from other household devices, such
as remote entry controls, security systems, and computers, may
interfere with the wireless transmission of this product and cause
temporary reception loss. This is normal and does not affect the general
performance of this product. Stable reception will resume once the
interference ends.
The remote transmitter should be placed in a dry shaded area.
NOTE: Fog and mist will not harm the remote transmitter but
direct rain must be avoided.
Mount the remote transmitter upright avoiding metallic objects
and frames, such as window sills. Verify that there are no obstacles
like a transmission tower or steep hill that can cause interference
and blockage between the remote transmitter and receiver.
Place the receiver unit at least 2 metres away from any electrical
devices, such as your television set, computer, cordless phone, or any
radio controlled equipment.
Replace unit(s) with fresh batteries when the Low Battery Indicator
lights up. Refer to the LOW BATTERY INDICATION section.
You may need to reposition the remote transmitter to a different
location and/or closer to the receiver for the best transmission.
The is an ideal feature to be used for greenhouses
and wine cellars, or any place that you require controlled temperature.
Once activated, the temperature alarm would sound when the room gets
too warm or too cold depending on your settings.
temperature alarm
You can set both an upper and lower temperature alarm for the local
temperature (main receiver unit) and/or for each of the remote
(outdoor) channels of 1 to 4.
Scroll to the Upper Temperature Alarm Setting mode by pressing .
You should see the symbol and dotted lines ( ) or pre-existing
setting blink.
MODE
---
Scroll to the Lower Temperature Alarm Setting mode by pressing .
You should see the symbol and dotted lines ( ) or pre-existing
setting blink.
MODE
---
Select the desired channel, local or remote channels (1 to 4) using .CHN
Select the desired channel, local or remote channels (1 to 4) using .CHN
Press to finish; or rMODE epeat steps for all
other channels if desired.
Press to finish; or rMODE epeat steps for all
other channels if desired.
NOTE: In the normal clock display, when either the upper or lower
temperature alarm has been set for a particular channel, the or
symbol will show up solid on the LCD screen when that channel is displayed.
Press or key to set the desired value for the upper temperature limit.+-
Press or key to set the desired value for the lower temperature limit.+-
To disable the particular alarm, press .
The dotted lines ( ) would reappear to indicate
that the alarm has been disabled.
ALARM
---
To disable the particular alarm, press .
The dotted lines ( ) would reappear to indicate
that the alarm has been disabled.
ALARM
---
WD633 Receiver
LOW BATTERY INDICATION
Replace the batteries when the Low Battery Indication ( ) lights up on
the middle-left portion of the LCD screen on the WD633 receiver.
NOTE: After replacing the batteries, you will need to perform the Setup and
Learn Function procedures again. Refer to the SETTING UP THE
TRANSMITTER/RECEIVER and WIRELESS TRANSMISSION sections.
A
A
C
Setting the Upper Temperature Alarm
Setting the Lower Temperature Alarm
UPPER TEMPERATURE LIMIT: warmIf the temperature gets too
and reaches the upper temperature limit, the alarm would sound.
LOWER TEMPERATURE LIMIT: coldIf the temperature gets too
and reaches the lower temperature limit, the alarm would sound.
MOONPHASE
MONDAY
CLOCK1
OUT
IN
TREND
MOONPHASE
MONDAY
CLOCK1
OUT
IN
TREND
When the Temperature Alarm Sounds
The temperature alarm will sound when the actual temperature has
reached (or exceeded) the upper or lower temperature limit.
The temperature alarm has a distinctive tone different to that of
Alarm 1 or Alarm 2.
or symbol and temperature limit will blink
Press ANY key to stop the temperature alarm. Or without interruption,
the temperature alarm will automatically stop after one minute.
PAGE 4
PAGE 13
PAGE 5
PAGE 14
PAGE 6
PAGE 15
1
1
1
1
4
WT440H Remote Transmitter
Replace the batteries when the Low Battery Indication lights up on
the bottom-left corner of the LCD screen on the WT440H transmitter.
When the batteries are low on a transmitter, a Low Battery Indication
( ) will also light up on the bottom-left corner of the LCD screen on
the WD633 receiver for that particular channel.
B
C
1
B
2
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für UPM WT440H wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info