MOONPHASE
MONDAY
CLOCK1
OUT
IN
TREND
TREND
1
2
3
4
5
6
Clock 1 Setting:
Clock 2 Setting:
Press and hold for 3 seconds to enter the clock setting mode. Y
will hear a beep. (The CLOCK 1 symbol will appear and the time will blink).
Press to set the hour and to set the minute;
Press during clock setting to change between 12 and 24
hour display. This also will end clock setting.
Press o no key press for one minute will end clock setting.
Scroll to Clock 2 mode using . (The CLOCK 2 symbol will appear).
Press or key to change the hour (in one hour increments/decrements
relative to Clock 1)
MODE
HOUR MINUTE
ALARM/( C/ F)
MODE
MODE
+-
°°
CL
1
4
5
3
2
6
Alarm 1 and Alarm 2 Setting:
Scroll to Alarm 1 using . The ALARM 1 symbol will appear
Press to set the hour
Press to set the minute
Press to toggle alarm on and off.
When the alarm is set ON, the symbol
will appear and the unit will beep.
In the normal clock display if the alarm is set ON,
the symbol will also appear on the display
MODE
HOUR
MINUTE
ALARM
.
.
When the Alarm Sounds:
or symbol will blink.
Press to snooze the alarm for 5 minutes.
After that the alarm will sound again.
Press ANY other key to stop the alarm. Or without interruption, the
alarm will automatically stop after one minute.
SNOOZE
T set Alarm 2, scroll to Alarm 2 using .
The ALARM 2 symbol will appear Follow the same
steps as above to set. In the normal clock display
if the alarm is set ON, the symbol will also appear
on the display.
MODE
N
ALARM SET
1
1
2
2
3
3
4
5
6
TROUBLESHOOTING
The remote (outdoor) readout on the receiver is
blinking.
The remote (outdoor) readout on the receiver is
blinking. The receiver will not detect or receive
the temperature and humidity data from the
remote transmitter
Function has been executed.
The temperature and humidity data on the
remote transmitter does not match the data
displayed on the receiver
The temperature and humidity data on the
remote transmitter does not match the data
displayed on the receiver
This may also be the result of a temporary loss of reception due
to interfering sources. Normal reception should resume once
the interference ends. Refer to the WIRELESS TRANSMISSION
section.
Re-synchronize the remote transmitter and receiver by pressing
and holding on the receiver for 3 seconds until a beep is
heard. The temperature and humidity data from the remote
transmitter will display on the receiver within 3 minutes. Refer to
the WIRELESS TRANSMISSION (Manual Learn Function) section.
CHN
Ensure the remote transmitter is away from any possible source of
interference and electrical disturbances. Y
the remote transmitter in a different location and/or closer to the
receiver The remote transmitter does have a maximum range of
40 metres, but any walls or windows the signal has to pass through
will reduce the distance. Due to the nature of the batteries,
extreme cold temperatures may also affect the transmission range.
Refer to the WIRELESS TRANSMISSION section and repeat the
Manual Learn Function with the remote transmitter in a new
location.
This may occur when you move the remote transmitter from one
environment to another For example, when you bring the
transmitter from inside the warm house out to the cold exterior In
such a case, there will be a big change in temperature. The
transmitter will record this change in temperature much quicker
than it is able to transmit the data to the receiver (which is done
once every minute). Therefore, you will temporarily get a
difference in reading between the remote transmitter and receiver
The solution is to allow the remote transmitter some time to sit in
its new location to reach equilibrium. This may take several
minutes. Once the data is stable, the data displayed on the
remote transmitter should match that displayed on the receiver
PROBLEM
SOLUTION
SPECIFICA
WD633 - WEA
- Battery T
- Operating T -5
- T Range: -9.9
-
°C °C
°C t °C
°C °C °C
Resolution: 0.1°C
to 50
o5
- Measurement Accuracy: Max. +/- 1 within measuring range of 0 to 40
WT440H - WEA
- Battery T
- Operating T -20°C to 60°C
- T Range: -30°C to 70°C
- T Resolution: 0.1°C for above -10°C / 1°C for below -10°C
- Measurement Accuracy: Max. +/- 1°C within measuring range of 0°C to 40°C
- Humidity Range: 25% to 90% RH (resolution 0.5%)
- T
- T
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
2. THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
FCC COMPLIANCE LIMITED TWO-
UPM warrants this product, excluding battery
use and service, for a period of two years from the date of purchase by the consumer
If, at any time during the warranty period, the product is defective or malfunctions, UPM shall repair or replace it (at
UPM's discretion) within a reasonable period of time.
If the product is defective,
(i) return it, with a dated proof of purchase, to the retailer from which you purchased it, or
(ii) package it carefully
postage prepaid, to the following address:
UPM Marketing Inc.
Return Goods
Unit 10B - 250 Shields Court
Markham, Ontario
L3R 9W7
This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by UPM that
the defect or malfunction was caused by damage which occurred while the product was in the possession of the
consumer
UPM's sole responsibility shall be to repair or replace the product within the terms stated above. UPM SHALL NOT BE
LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND
RESUL FROM ANY BREACH OF ANY W
OTHER FAIL Some states do not allow the exclusion or limitation of incidental or
consequential damages, so this limitation may not apply to you.
THIS WARRANTY IS THE ONL THE DURATION OF ANY
IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANT
PURPOSE, IS HEREBY LIMITED TO THE TWO YEAR DURA Some states do not allow
limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which may vary from state to state.
If you have any questions concerning this warranty
UPM Marketing Inc.
Customer Service Department
Unit 10B - 250 Shields Court
Markham, Ontario
L3R 9W7
Or call 1-888-GO-TO-UPM (1-888-468-6876), Monday to Friday
(2)
CUSTOMER SUPPORT HOTLINE: 1-888-468-6876
2
1
6
1
4
2
5
3
3
MOON PHASE
MOON PHASE
MOON PHASE
MOON PHASE
MOON PHASE
MOON PHASE
MOON PHASE
MOON PHASE
MOON PHASE
Moon Phase Display
MOON PHASE DISPLA
The moon phase is automatically updated according to the calendar setting.
New Moon
9
New Moon
1
Y Crescent
2
First Quarter
Waxing Gibbous
Full Moon
Waning Gibbous
Last Quarter
Old Crescent
8
7
6
5
4
3
ALARM 1
MONDAY
CLOCK1
MONDAY
CLOCK1
Alarm 1 Setting
Clock Display
P
P
P
P
P
P
