Bedienungsanleitung Vaillant ecoVIT exclusiv VKK 366-4 (Seite 11 von 16) (Englisch)

748582

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Care and maintenance 5

0020258609_00 ecoVIT exclusiv Operating instructions 11

5.3.2 Filling the heating installation

Caution.

Risk of material damage due to heating

water that is extremely calciferous or cor-

rosive or contaminated by chemicals.

Unsuitable tap water damages the seals

and diaphragms, blocks components in the

product and heating installation through

which the water flows and causes noise.

▶ Only fill the heating installation with suit-

able heating water.

▶ In case of doubt, ask a competent person

for details.

1. Ask a competent person where the filling cock is loc-

ated.

2. Connect the filling cock to a hot water supply in the way

you were told by the competent person.

3. Open all radiator valves (thermostatic radiator valves) of

the heating installation.

4. Open the hot water supply.

5. Slowly open the filling cock.

6. Fill it with water until the required filling pressure is

reached.

7. Close the hot water supply.

8. Purge all radiators.

9. Then check the filling pressure on the display.

10. Top up with more water if necessary.

11. Close the filling cock.

5.4 Checking the condensate discharge pipe

and tundish

The condensate discharge pipe and tundish must always be

penetrable.

▶ Regularly check the condensate discharge pipe and tun-

dish for faults and, particularly, for blockages.

You must not be able to see or feel any obstructions in the

condensate discharge pipe and tundish.

▶ If you notice a fault, have it eliminated by a competent

person.

5.5 Carrying out the flue gas analysis

Note

Measurement and inspection work must only be

carried out by the chimney sweep or competent

person.

1 + button 2 − button

1. Switch on the chimney sweep function by pressing the

− and + buttons for the DIA system at the same time.

◁ Shown in the display: S.Fh = Heating chimney

sweep mode; S.Fb = Domestic hot water chimney

sweep mode

◁ The product now works at maximum load for 15

minutes. If you do not press any buttons for 15

minutes or if a flow temperature of 85 °C is reached,

the chimney sweep function is automatically

switched off.

2. Take the measurements at the earliest after three

minutes of the product operating.

Applicability: VKK 226/4, VKK 286/4, VKK 366/4

▶ Remove the upper casing (→ Installation instructions).

▶ Use the test points that are underneath for the meas-

urement (→ Installation instructions).

Applicability: VKK 476/4, VKK 656/4

1 Flue gas test point 2 Fresh air test point

▶ Use the test points on the adapter for the measure-

ment, as shown.

3. Unscrew the sealing cap from the flue gas test point (1).

4. Remove the sealing cap from the combustion air test

opening (2).

5. Take the measurements in the flue gas route at the flue

gas test point.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vaillant ecoVIT exclusiv VKK 366-4 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Vaillant ecoVIT exclusiv VKK 366-4

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info