Bedienungsanleitung Vaillant ecoVIT exclusiv VKK 366-4 (Seite 12 von 16) (Englisch)

748582

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

6 Troubleshooting

12 Operating instructions ecoVIT exclusiv 0020258609_00

– Immersion depth: ≈ 80 mm

6. Take measurements in the air route on the combustion

air test opening (2).

– Immersion depth: ≈ 10 mm

7. Switch off the chimney sweep function by pressing the

− and + buttons for the DIA system at the same time.

8. Screw the sealing cap onto the flue gas test point (1).

9. Fit the sealing cap onto the combustion air test opening

(2).

Applicability: VKK 226/4, VKK 286/4, VKK 366/4

▶ Install the upper casing (→ Installation instructions).

6 Troubleshooting

6.1 Eliminating faults

▶ Use the table in the appendix to attempt to eliminate

faults.

Troubleshooting (→ Page 14)

▶

Press (max. three times) to restart the product.

▶ If you are unable to eliminate the fault and the fault re-

curs despite reset attempts, contact an approved heating

specialist company.

6.2 Checking the product status

Heizbetrieb - Bren

1 Display 2 i button

1. Call up the product status by pressing the i button.

2. Switch the display back to normal operating mode by

pressing thei button.

7 Decommissioning

7.1 Temporarily decommissioning the product

Caution.

Risk of material damage due to frost

The frost protection and monitoring devices

are only active while the unit is connected to

the power mains, the product is switched on

via the main switch and the gas stopcock is

open.

▶ You must use the control if you want to

activate and deactivate the product in

normal mode.

▶ If no control is present when a main switch

has been switched on, set the rotary

knobs for the target heating flow and

cylinder values to the anti-clockwise end

stop.

▶ Do not disconnect the product from the

power mains when it is in normal mode.

▶ Leave the main switch in position 1 in

normal mode.

1 Main switch

2 Heating flow temperat-

ure rotary knob

3 Cylinder temperature

rotary knob

1. Turn the rotary knob for the cylinder temperature (3)

anti-clockwise as far as it will go.

2. Turn the rotary knob for the heating flow temperature

(2) anti-clockwise as far as it will go.

3. If the fan continues to run, wait until it stops.

◁ "Fan overrun" is shown in the display.

4. Turn the main switch (1) to position 0.

5. Close the gas stopcock and the cold-water isolation

valve.

Note

The isolators are not included in the scope of

delivery for your product. They are installed

on-site by the competent person. Ask the

competent person to explain where the isol-

ators are located and how they are operated.

7.1.1 Draining the heating installation

Another way to protect the heating installation and the

product from frost for very long switch-off periods is to drain

them completely.

▶ Consult a competent person about this.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vaillant ecoVIT exclusiv VKK 366-4 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Vaillant ecoVIT exclusiv VKK 366-4

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info