Bedienungsanleitung Vaillant VRS 560 (Seite 15 von 40) (Englisch)

469501

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

3Installation instructions – auroMATIC 560 0020008427_01

3 Safety instructions and regulations

3.1 Safety instructions

The controller must be installed by a qualified engineer,

who is responsible for adhering to the existing stand-

ards and regulations. We accept no liability for any dam-

age caused by failure to observe these instructions.

Danger!

Risk of fatal electric shock from touching live

connections.

Before working on the unit, switch off the

power supply and secure against restart. Only

remove the controller from the wall installation

or it pull out of the plinth once the power sup-

ply has been switched off.

3.2 Regulations

All wiring must be in accordance with Building Regula-

tions Part P and BS 7671 (IEE Wiring Regulations), and

must be carried out by a suitably qualified person.

Use standard wires for wiring.

Minimum cross-section of wires:

– Power supply 230 V

(pump connection cable): 1.5 mm

– Extra-low voltage lines

(sensor wires): 0.75 mm

Connections with 230 V and sensor wires must be laid

separately if longer than 10 m.

230 V connection leads must be supplied in 1.5 mm

and

fastened to the wall installation using the accompanying

cable clamps.

Do not use free terminals on the appliances as support

terminals for other wiring.

The controller must be installed in a dry room.

Danger!

Danger of scalding due to hot water!

The temperature of the solar hot water storage

tank may sometimes be considerably higher

than 60 °C (due to the solar heating, but also

the anti-legionella function, if activated).

Have your expert technician install a mixer

valve with cold water supply without fail.

Have the mixer valve adjusted by your expert

technician.

4 Assembly

4.1 Scope of delivery

Using Table 4.1, verify the scope of delivery for the con-

troller set.

Item Quantity Components

1 1 auroMATIC 560 controller

2 1 VR 11 collector sensor

3 3 VR 10 standard sensor

4 1 C1/C2 cable

Table 4.1 Scope of delivery

4.2 Assembly of VR 10 standard sensor

The VR 10 standard sensor is designed so that it can be

used as an immersion sensor or surface mount sensor.

When used as a surface mount sensor, the sensor is se-

cured to the forward flow pipe or the return pipe using

the supplied tension band. In order to guarantee good

heat transfer, the sensor is flat on one side. We also rec-

ommend that the pipe with the sensor is insulated, in

order to enable the best possible measuring of tempera-

ture.

Fig. 4.1 VR 10 standard sensor

4.3 Accessories

The following accessories are necessary in order to con-

nect a second collector field or an additional solar cylin-

der to the controller, and to enable measurement of the

solar yield.

4.3.1 VR 10 standard sensor

The use of additional standard sensors is necessary if

you want to connect a second solar cylinder to the con-

troller.

4.3.2 VR 11 collector sensor

If a second collector field is connected, it is necessary to

install a second collector sensor from the Vaillant acces-

sory range.

Safety instructions and regulations 3

Assembly 4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vaillant VRS 560 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Vaillant VRS 560

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info