469501
16
Zoom out
Zoom in
Vorherige Seite
1/40
Nächste Seite
Installation instructions – auroMATIC 560 0020008427_014
4.4 Installing the controller housing
The controller is designed to be mounted on a wall and
is equipped with System ProE terminal strips. These ter-
minals must be used for all connections made at the in-
stallation site.
Fig. 4.2 Opening the controller housing
The cover consists of two parts, which can be removed
separately.
As shown in Fig. 4.2, pull the lower front cover off of
the controller housing.
C1/C2
C1 C2
KOL1
21
SP1
21
SP2
21
SP3
21
Ertrag
21
KOL2
21
230 V~
PE N L
KOL1-P
PE N L
LEG/BYP
PE N L
LP/UV1
PE N L
EP
21
KOL2-P/Z P
PE N L
12
Fig. 4.3 Fastening the controller housing
Mark the position of both holes (1 and 2) and drill the
bore holes.
Select the wall plugs to suit the state of the wall, and
screw the controller housing on tightly.
ProE-system wiring
C1/C2
C1 C2
KOL1
21
SP1
21
SP2
21
SP3
21
Ertrag
21
KOL2
21
230 V~
PE N L
KOL1-P
PE N L
LEG/BYP
PE N L
LP/UV1
PE N L
EP
21
KOL2-P/Z P
PE N L
3
Fig. 4.4 Fold-up the control panel
Fold the control panel towards the top.
Wire the controller according to the selected hydraulic
plan (see Section 5.1).
Secure all cables with the accompanying cable clamps
(3).
Fold the control panel back down.
Attach the front cover again.
5 Electrical installation
The electrical connection may only be carried out by an
approved specialist company.
e
Danger!
Risk of fatal electric shock from touching live
connections. Before working on the appliance,
turn off the power supply and secure against
restart.
a
Caution!
The circuit board can be damaged if short
circuited through the connection leads. For
safety purposes, a max. of 30 mm of insulation
may be removed from the ends of 230 V leads
which will be connected to ProE plugs. If more
insulation is removed, there is a risk of short
circuiting the circuit board.
Caution!
When exchanging the controller in an existing
system, sensor-curve characteristics should be
taken into consideration (see Sec. 11), and the
sensors should be replaced if necessary!
4 Assembly
5 Electrical installation
16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Vaillant VRS 560 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Vaillant VRS 560

Vaillant VRS 560 Bedienungsanleitung und Installationsanweisung - Holländisch - 40 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info