Bedienungsanleitung Valor 722AN (Seite 17 von 20) (Englisch)

611085

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

16. OPERATING INSTRUCTIONS

16.1 The flame sensing device.

For your safety, your fireplace is fitted with a

mechanism, which will automatically shut off the

gas supply to the fire if the pilot flame goes out. It

will also shut off the gas supply if the vent is

blocked or if there is not enough ventilation.

This mechanism incorporates a probe, which senses

that the heat from the pilot flame is correct. If this

probe is cool, the device will prevent any gas flow

unless the sliding control button is held at the

ignition position.

The fireplace is also fitted with a mechanism, which

will automatically shut off the fire if the vent is

blocked.

If this safety mechanism frequently shuts off the gas,

get expert advice.

16.2 Lighting

Full lighting instructions are on the next page.

Note that when first turned on the flames will

predominantly blue. The coals will take time to

warm up. Although some glow will be seen after

approximately ten minutes, the full visual effect will

only be apparent after a somewhat longer time.

Lighting with a long match

In the unlikely event of failure of the ignition spark,

the pilot can be lit by a long match. Insert the match

alongside the left side wall of the fire box and

operating the slide control as described in the

normal lighting instructions.

16.3 Cleaning

Turn the fire off and allow it to cool before

attempting any cleaning. Note that the fire will

retain heat for some time after it has been turned off.

Metal parts

Clean the metal parts with a slightly damp cloth and

then dry. Do not use abrasive cleaners, they could

scratch the surface.

Coals and ceramic firebox walls

Dust etc. Can be brushed from the coals after

removing the safety guard. We suggest that you

remove the coals in the reverse order to that shown

fitting instructions. Make sure that no particles are

brushed into the ceramic burner slots.

Ceramic burner

Remove any dust or other foreign matter from the

solid areas of the burner with a dry soft brush. Be

careful not to brush any particles into the open slots.

Remove any particles from the slots with a vacuum

cleaner fitted with a soft brush attachment. Do not

poke wire, etc. into the slots in the burner.

16.4 Checks

16.4.1 A periodic visual check of the pilot and burner

flames should be made. Compare the burner flames

to those illustrated in figure 32. The pilot flame

should be visible between the coals near the front

left corner as illustrated in figure 33.

Check after the fire has been on for at least 30

minutes.

16.4.2 Keep area in front of the ashpan cover clear to

prevent obstruction of air flow to appliance for

combustion.

16.4.3 The flow of combustion and ventilation air must

not be obstructed. The venting system should be

examined by a qualified agency regularly. We

suggest annually.

Fig.32 Main flames

Fig.33 Pilot flame

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Valor 722AN Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info