Bedienungsanleitung Valor 722AN (Seite 18 von 20) (Englisch)

611085

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

16.5 Lighting instructions

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property

damage, personal injury or loss of life.

A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these

instructions exactly.

B.BEFORE LIGHTING smell all round the appliance area for gas. Be sure to smell next to the floor because

some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

C.Use only your hand to turn the gas valve knob and move the control slide knob. Never use tools. If the

knobs will not move correctly by hand, don’t try to repair them, call a qualified service technician. Force

or attempted repair may result in a fire or explosion.

D.Do not use this appliance if any part has been under water. Immediately call a qualified service technician

to inspect the appliance and to replace any part of the control system and any gas control which has been

under water.

LIGHTING INSTRUCTIONS

1. STOP! Read the safety information above on this label.

2. Turn the gas valve control counterclockwise as far as it will go (shut).

3. Move the control slide knob up to “Off”.

4. Wait five (5) minutes to clear out any gas. then smell for gas, including near the

floor. If you smell gas, STOP! Follow “B” in the safety information above. If you

don’t smell gas, go to the next step.

5. Find the pilot. It is at the left side of the fire box near the front corner.

6. Turn the gas valve control clockwise as far as it will go (open).

7. Slide the control slide knob to the bottom (ignition) position marked and hold

down . The pilot should light.

If the pilot does not light at all during several attempts, try lighting with a long

match as described below.

8. Keep the slide knob held down for a further 10

seconds then release. The knob should pop up to the

low heat position and the burner should light at low

heat.

• If the pilot does not light or stay lit repeat steps 2

through 8.

9. Move the control slide knob to the desired setting

between low heat and high heat.

10.Replace the ashpan cover.

Match Lighting: Apply a long match to the pilot while

the gas valve is open and

the control slide knob is held at the ignition position.

• If the pilot or burner will not light or stay lit after several tries of all the above steps, shut the gas valve

control and call your service technician or gas supplier.

TO TURN OFF GAS TO APPLIANCE

1. Move the control slide knob past the high heat position to “O” (Off).

2. Turn the gas valve control counterclockwise as far as it will go (shut). Do not force.

Control slide knob

Gas Valve control

Pilot

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Valor 722AN Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info