Bedienungsanleitung Varo POWXG9100 (Seite 6 von 13) (Englisch)

756798

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

POWXG9100 EN

WARNING: High Pressure hoses, fittings, and couplings are important for the safety of the

appliance. Use only fittings and couplings recommended by the manufacturer.

Do not use the appliance, if a supply cord or important parts are damaged, e.g. safety devices,

high pressure hoses, trigger gun.

WARNING: Incorrect fuels shall not be used as they may prove hazardous.

WARNING: Do not use combustion engine powered appliances indoors unless adequate

ventilation is assessed by national labour authorities.

WARNING: Ensure that any exhaust emissions are not in the vicinity of air intakes.

7 SAFETY WARNINGS GASOLINE

WARNING: Use extra care in handling fuels. They are flammable and the vapours are

explosive. The following points must be observed.

 Use only an approved container.

 Never remove the fuel cap or add fuel with the power source running. Allow engine

exhaust components to cool before refuelling.

 Do not smoke.

 Never refuel the machine indoors.

 Never store the machine or fuel containers inside, where is an open flame, such as a

water heater.

 If fuel is spilled, do not attempt to start the power source, but move the machine away

from the area of spillage before starting.

 Always replace and securely tighten the fuel cap after refuelling.

 If the tank is drained, this should be done outdoors.

8 SAFETY FEATURES

8.1 Thermal relief valve

A thermal relief valve is provided to protect the pump from overloading if the spray gun is

closed for an extended length of time or the nozzle becomes plugged. However, it is intended

to be used as a backup system and avoid the overheating of the pump.

Switch the pressure washer "OFF", if it will not be used for longer than five minutes. This

reduces wear, prevents fuel consumption and extends the live of the pump by avoiding heat.

8.2 Safety lock off latch

To prevent accidental discharge of high pressure water, the safety latch on the trigger should

be engaged whenever the pressure washer is not in use (refer to operating instruction).

8.3 Water temperature protection

If the water temperature in the pump is higher than 50 °C, the protection valve will open and

release the hot water to protect the pump. And after the hot water is out, the valve will close

again.

9 ASSEMBLY INSTRUCTIONS

Remove all packaging materials from the unit. Check the main unit, its components and all

accessories for loss and transport damages.

9.1 Assembly of the wheels (Fig. 1)

Drive the axle through the centre hole of the wheel until the pin is blocked.

 Assemble the wheel on the axle and fix it with a nut.

9.2 Assembly of the hose reel (Fig. 2)

 In the direction of the arrow, fix the hose reel on the frame.

 In the direction of the arrow, insert the handle into the frame, lock it by lock catch A.

 In order to avoid the hose reel moving, fix it with screw and nut.

9.3 Assembly of the handle (Fig. 3)

 In the direction of the arrow, insert the handle into the mounting hole of hose reel

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Varo POWXG9100 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Varo POWXG9100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info