Bedienungsanleitung Varo POWXG9100 (Seite 7 von 13) (Englisch)

756798

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

POWXG9100 EN

9.4 Assembly of the panel and lance hook (Fig. 4)

Mount the panel with the 4 screws M6x50 and 4 lock nuts M6.

9.5 Assembly of the spray gun (Fig. 5-6)

Fit the lance to the gun. Grip the end of the gun and screw the lance onto the gun ensuring it

is tight. Do not over tighten as this could damage both the connectors

Connect the high pressure hose connector to the connector on the underside of the gun

assembly ensuring that it is tight. Do not over tighten as this could damage both the

connectors.

10 BEFORE OPERATION

To prepare your pressure washer for operation, you will need to perform these tasks:

 Add oil to engine crankcase.

 Add fuel to fuel tank.

 Connect high pressure hose to spray gun and pump.

 Connect water supply to pump.

 Attach nozzle extension to spray gun.

Note: the engine and pump on your new pressure washer will often have an improved

performance after a break of several hours.

10.1 Add oil to the engine crankcase (Fig. 7)

Do not attempt to start the pressure washer without filling the engine crank case with the

proper amount and type of oil (15W-40). In delivery status the pressure washer has no oil

inside the engine crank case. Operating the unit without oil will cause engine damage. Place

the machine on a level surface and remove the oil filler cap.

The engine has two oil fill points at the front and back of the engine. Remove the desired cap

and fill with the engine oil specified to the upper level mark.

Add engine oil to at least half of the dipstick.

The engine is equipped with an oil level sensor. The oil level sensor

switches the engine off if the oil level is too low and prevents a restart. If

the engine cuts out although the oil level is correct, check whether the

petrol-powered high-pressure cleaner is standing straight.

10.2 Add fuel to fuel tank (Fig. 8)

The pressure washer is powered by a four-stroke engine (14), which uses unleaded petrol

fuel.

Use a suitable funnel to fill in the fuel to the engines fuel tank (11). Do not spill any fuel or

overfill the tank. The fuel tank should not be filled above the top of the fuel filter.

10.3 Connecting the water hose to the High pressure washer (Fig. 9)

 Run water through the hose for a few seconds to flush any debris from the hose.

 Inspect inlet screen and remove any debris.

 Connect hose to water inlet and tighten by hand.

 Turn on water.

Do not run the pump without connecting to the water supply and turning

the water on. Such failure can damage the pressure washer.

10.4 Connect the high-pressure hose to the delivery pipe outlet (Fig .10)

 Attach the end of the high pressure hose to the high pressure outlet.

 Turn on the water supply and squeeze the gun trigger until the water flows in a steady

stream through the lance. Do not use water which exceeds 50 °C.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Varo POWXG9100 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Varo POWXG9100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info