Bedienungsanleitung Velodyne SC-IC (Seite 17 von 30) (Englisch)

567843

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

www.velodyne.com

SC-1250 Amplier User’s Manual - 11

A Word About Subwoofer Placement

Subwoofers operate at extremely low frequencies, which are primarily omni-directional. Keep in mind that

frequencyresponseandoutputlevelcanbedrasticallyinuencedbyplacement,dependingontheacoustic

properties of the listening room. Typically, the optimum location for a subwoofer is in a front corner of your

listeningroom.Thislocationwillusuallyoerthegreatestoutputlevelsandoptimumlowfrequencyextension.

The worst location for a subwoofer is typically far away from any walls, close to the center of your room and near

an opening or doorway. Avoid these locations when possible. When using a pair of SC subwoofers in stereo, it

is preferable to place each subwoofer by the satellite of the same channel. Typically, a minimum distance of one

to two feet from your TV to the subwoofer will be adequate to avoid any magnetic interference.

Remember that the built-in 7 band EQ will help to get the most performance out of your subwoofer no matter

where it is placed.

Caution!

This amplier has electronics built into the cabinet. Do not place the amplier next to sources of heat such as

furnace registers, radiators, etc. Likewise, do not place the amplier near sources of excessive moisture, such as

evaporative coolers, humidiers, etc. The power cord should be routed in such a way that it will not be walked

on, pinched or compressed in any way that could result in damaging the insulation or wire.

SELECTING THE SUBWOOFER(S) TO BE CONTROLLED

Your SC-1250 can control a variety of Velodyne SubContractor Series subwoofers as well as generic passive

subwoofers.Specialinternalsoftwaresettingsaredesignedtomaximizeperformanceandreliabilitydepending

on the model of subwoofer being controlled, so it is important to match the SC-1250 amplier with the

subwoofer(s) it is controlling. The SC-1250 comes with a default setting for the SC-10 subwoofer. When the

unitisrstpoweredup,themodelbeingcontrolledisdisplayedfor2secondsonthenumericLEDbeforethe

display reverts to the volume setting. The subwoofer to be controlled is shown as follows:

** - The generic subwoofer setting is for passive subwoofers not on the above list. CAUTION: there is no anticlipping or anti-

distortion protection on this setting.

Tochangethesubwoofertobecontrolled,rstpowerdowntheamplierusingthepowerswitchontheback

panel (DO NOT use the power button on the front panel). Then, turn the switch on while depressing any of the

buttons on the front panel (crossover up or down, or volume up or down). The unit will show the model it is

currently controlling. To change the model, simply push the crossover up or crossover down buttons and the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Velodyne SC-IC Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info