Bedienungsanleitung Velodyne SC-IC (Seite 18 von 30) (Englisch)

567843

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

www.velodyne.com

12 - SC-1250 Amplier User’s Manual

model changes on the LED display. Once the desired model is seen on the LED display, simply release the

button. You don’t need to do anything else - the model to be controlled is automatically stored in the SC-1250’s

memory. To exit model selection mode, use the power switch on the back panel to power down and power up

the unit. You should see the model you selected for 2 seconds on the LED display before the display reverts to

the volume.

Using the SC-1250 to Drive Two Subwoofers

Oncethemodelselectionprocessiscompleted,nootheradjustmentsareneededtoenabletheSC-1250to

drive one or two subwoofers.

USAGE

Thissectionaddressesday-to-dayusageofyourSC-1250amplier.

Remote Control

The features of the SC-1250 remote control are listed below.

• POWER — This button forces your SC-1250 unit into standby

mode. The power LED turns amber, the numeric LED shuts

o,andtheamplierputsoutnopower.Theunitwillremain

in this mode until the POWER button is pressed again. To fully

deactivate (i.e. power down) the unit, press the power switch

on the front panel.

Note: The master power switch on rear panel must be on in

order for the front power button to function.

• MUTE — This button mutes the subwoofer. The LED on the

amplier will show 00 if the unit is muted. To unmute the

subwoofer, press the MUTE button again and the original

volume setting shows on the LED.

Figure 6: SC-1250 Remote.

• EQ — ThisbuttonautomaticallyEQsthesubwooferusinga7bandinternalgraphicequalizer.Tousethis

feature,rstplugthesuppliedmicrophoneintotheMic-Injackonthebackpanelofthesubwooferand

place the mic in your preferred listening position. Then, by pressing EQ on the remote, the subwoofer

emits12 “sweeptones” thatcover thefrequenciesbetween 20and 150Hz. TheLED displays“AU”

during the Auto-EQ process. After the sweeps are complete, the unit saves its EQ settings and returns to

normal operation. To prevent accidental invocation of the EQ feature, you must hold down the EQ button

for 2-3 seconds before the EQ sweeps begin.

Note:EachtimetheEQfeatureisutilized,theEQsettingsfortheSC-1250arereset.Ifthemicrophone

is not plugged in, the SC-1250 will emit one or two sweep tones then cease the EQ operation. In this

case, the previous EQ settings will be preserved.

• PHASE —Thesebuttonsallowyoutooptimizethesubwooferperformanceforthelocationandyour

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Velodyne SC-IC Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info