Bedienungsanleitung Vermont Castings Intrepid - Gas (Seite 9 von 64) (Englisch)

815509

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

993-90-30007474Vermont Castings • Intrepid DV-IFT Owner’s Manual_R28 • 11/23

Vertical Termination

A vertical vent system must terminate no less than 8’ (2.44

m) and no more than 40’ (12 m) above the appliance ue

collar. There is a restrictor plate installed in the stove from the

factory. A extra vent restrictor plate (included in the manual

bag) can be added within the venting to reduce draft in a

high draft situation. Fine tune adjustments can be made

to compensate for draft characteristics that could interfere

with proper ame height and operation. Note: There is no

adjustability within the rebox for high draft situations.

A vertically terminated vent system must also conform to the

following criteria:

• No more than four 90° elbows may be used.

• Two 45° elbows may be substituted for one 90° elbow.

No more than six 45° elbows may be used.

• Vent must rise a minimum of 2 feet (610mm) after the

initial elbow on the back of the unit before an additional

o󰀨set is used.

• Termination height must conform to roof clearance as

specied in Figure 2.9.

Figure 2.9 - Vertical vent termination window.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

Vertical Run (in feet)

(Measured after the first elbow. (Transition elbow)

Horizontal Run (in feet)

2ND FLUE

RESTRICTOR

1 FLUE

RESTRICTOR

DARK GREY AREA

IS UNACCEPTABLE

VENTING

Vent Termination Clearances

When planning the installation, consider the location of the

vent terminal and clearances. Some of the most common

clearances to keep in mind are shown in Figure 2.10.

Important:All vent clearances must be maintained.

Check your vent termination clearances against Figures

2.10 and 2.11.

The vent should be placed so that people cannot be burned

by accidentally touching the vent surfaces when the stove

is operating.

The vent termination should be located where it cannot be

damaged by such things as automobile doors, lawn mowers

or snowblowers and it should be located away from areas

where it could become blocked by snow, etc.

Some considerations are:

• Obstructions or impediments to venting.

• Nearby combustible materials that could come into

contact with combustion exhaust gases.

• Other nearby openings {within 12" (305 mm)} through

which exhaust gas could reenter the building.

• All vegetation within 3’ (76 mm) that may interfere with

the draft.

Other factors that inuence where the installation will be

sited include the location of outside walls, where additional

heat may be desired in the home, where the family members

gather most regularly, and perhaps most importantly, the

distance limitations of the venting system.

IMPORTANT

The horizontal termination must not be recessed into

the exterior wall or siding.

Horizontal vent runs must be level toward the vent

termination.

Clearances around the vent termination must be

maintained.

For installations using DuraVent pipe, parallel installations

with minimum wall clearance have restricted access for

connecting the Horizontal Vent Cap straps to the vent

pipe. See the maker’s instructions for recommended

installation procedures.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vermont Castings Intrepid - Gas Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info