Bedienungsanleitung Vermont Castings Intrepid - Gas (Seite 23 von 64) (Englisch)

815509

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

2323 3-90-30007474Vermont Castings • Intrepid DV-IFT Owner’s Manual_R28 • 11/23

NOTES:

1. The horizontal run of venting must be level, or have a

1/4” (6 mm) rise for every 1’ (305 mm) of run toward

the termination. Never allow the vent to run downward.

A downward slope can trap heat and become a possible

re hazard.

2. Horizontal vent runs of vent pipe must be supported to

prevent any downward sags. Horizontal pipe sections

should be supported at least every 5’ (1.5 m). Wall straps

can be used for this purpose. Alternatively, plumbers

tape or other suitable noncombustible material can be

used to support the vent pipe.

3. DirectVent Pro and SLP venting requires no sealant.

Step 3 - With the appliance adapter and pipe section

attached, slide the stove into its correct location. Mark the

wall for a square hole that measures 10” x 10” (254 x 254

mm). The centerline of the pipe should line up with the center

of the square hole, Figure 3.25. Cut and frame the square

hole in the exterior wall where the vent will be terminated. If

the wall being penetrated is constructed of noncombustible

material only, i.e. masonry block, brick or concrete only, a

hole with zero clearance is acceptable.

ST977

simp twist lock

8/07

Figure 3.24

St977

simpson framing

8/07

Center

of Hole

Figure 3.25

Step 4 - Position the horizontal termination cap in the center

of the square framed hole, and attach to the exterior wall

with the four (4) wood screws provided. Before attaching

the vent termination cap to the exterior wall, run a bead of

non-hardening silicone sealant around the outside edges to

make a seal between the cap and the wall. The arrow on the

vent cap should be pointing up. Ensure proper clearances

to combustible materials are maintained, Figure 3.28.

12” (305 mm)

Minimum

ST979

simpson snorkel

8/07

12”

(305 mm)

Figure 3.26

St980

simp snork drain

03/19

12” Min

(305 mm)

Adequate

Drainage

Grade

Snorkel

Figure 3.27

2. The location of the horizontal vent termination on an

exterior wall must meet all local and national building

codes, and must not be easily blocked or obstructed.

Refer to "Vent Termination Clearances" for proper

Termination Clearances.

For installations requiring a vertical rise on the exterior of

the building, 14” (356 mm) and 36” (914 mm) tall snorkel

terminations are available, Figure 3.26. Follow the same

installation procedures as used for standard horizontal

terminations. If the snorkel termination must be installed

below grade level, (i.e. basement application), proper

drainage must be provided to prevent water from entering

the snorkel termination, Figure 3.27. Do not attempt to

enclose the snorkel within the wall or any other type of

enclosure.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vermont Castings Intrepid - Gas Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info