Bedienungsanleitung Vermont Castings Intrepid - Gas (Seite 25 von 64) (Englisch)

815509

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

2525 3-90-30007474Vermont Castings • Intrepid DV-IFT Owner’s Manual_R28 • 11/23

Step 2 - Set the gas

appliance in the desire

location. Drop a plumb bob

down from the ceiling to the

position of the appliance

ue exit, and mark the

location where the vent will

penetrate the ceiling. Drill a

small hole at this point. Next,

drop a plumb bob from the

roof to the hole previously

drilled in the ceiling, and

mark the spot where the

vent will penetrate the roof,

Figure 3.32. Determine if

ceiling joists, roof rafters,

framing or other materials

will obstruct the venting

system. You may wish to

relocate the appliance or to

o󰀨set, to avoid cutting load-

bearing members.

Step 3 - To install the round

ceiling support/wall thimble

cover in a at ceiling, cut a

10” x 10” (254 x 254 mm)

square hole in the ceiling

(unless otherwise specied)

centered on the hole drilled

in Step 2. Frame the hole as shown in Figure 3.33.

Step 4 - Assemble the desired pipe sections and elbows

necessary to reach from the appliance adapter up through

the round ceiling cover or support box. Ensure that all pipe

and elbow connections are in their fully twist-locked position.

Step 5 - Cut a hole in the roof centered on the small drill

hole placed in the roof in Step 2. The opening should be

of su󰀩cient size to meet the minimum requirements for

clearance to combustibles, as specied.

B984

install thimble cover

8/07

Wood Screws

Figure 3.31

ST984

straight up locat

8/07

Mark Location

Mark and Drill

Plumb Bob

Figure 3.32

NOTES:

1. If exact lengths or

distances must be met

between elbow o󰀨sets or

elsewhere, use the pipe

extensions to adjust onto

standard pipe sections,

Figure 3.34.

2. If an o󰀨set is necessary

in the attic to avoid

obstructions, it is

important to support

the vent pipe in order to

avoid excessive stress

on the elbows. Wall

straps or plumber tape

may be used for this

purpose, Figure 3.35

3. Wherever possible, use 45° elbows instead of 90°

elbows. The 45° elbow o󰀨ers less restriction to the ow

of ue gases and intake air.

Step 6 - Slip the roof ashing over the pipe section(s)

protruding through the roof. Use a non-hardening sealant

between the roof ashing and the roong to prevent water

leakage. Secure the base of the roof ashing to the roof with

roong nails.

ST988

offset

8/07

Wall Strap /

Plumbers Tape

45° Elbow

Figure 3.35

ST986

thru ceiling

8/07

Ceiling Joists

Cut and

Frame

1-1/2" Wood

Screws

Decorative

Ceiling Support

Cover

Figure 3.33

Continue to assemble

pipe sections and elbows

as necessary to reach

up through the rooine.

Galvanized pipe and

elbows may be utilized in

the attic, as well as above

the rooine. The galvanized

nish is desirable above

the rooine, due to higher

corrosion resistance.

Figure 3.34

ST987

pipes

8/07

Pipe

Extension

Pipe

Section

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vermont Castings Intrepid - Gas Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info