Bedienungsanleitung Vermont Castings Stardance Series (Seite 37 von 54) (Englisch)

815508

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

3737 3-90-30007467Vermont Castings • Stardance SDDVT Installation Manual_R35 • 11/23

M.Troubleshooting

With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do

experience a problem, this troubleshooting guide will assist a qualied service technician in the diagnosis of a problem and

the corrective action to be taken. This troubleshooting guide can only be used by a qualied service technician. Contact your

dealer to arrange a service call by a qualied service technician.

IntelliFire™ Touch

Error Codes

ECM LED

Error Codes Description

3 Red: 1 Green IFT-RC400 error message: ‘Appliance Safely Disabled’, pilot sparks for 90 sec, no ame-rectication.

2 Red: 1 Green IFT-RC400 display: ‘Error Pilot Flame’, pilot valve solenoid not detected.

2 Red: 2 Green Sparking feedback signal error, spark coil failure.

5 Red: 1 Green IFT-RC400 display: ‘Error Power Vent’ (if installed).

See Troubleshooting matrix for more detail on Lock-out Error Codes, Possible Causes and Corrective Actions.

Troubleshooting:

Symptom PossibleCause Corrective Action

Pilot won’t light, module clicks but no

spark 90 sec, 3 Red/1 Green Lock out.

Incorrect wiring. Verify ‘S’ (White) sense wire and ‘I’ (orange) ignitor wire

are connected to correct terminals on IFT-ECM.

Loose connections or

electrical shorts in wiring.

Verify no loose connections or electrical shorts in wiring

from module to pilot assembly. Verify wire insulation is not

damaged. Verify wires are not grounding out to chassis,

pilot burner, or any other metal object. Replace any

damaged wires.

Ignitor gap is too large. Verify spark gap is approximately 0.095” (2.41 mm) to

0.135” (3.43 mm).

Pilot won’t light, there is no noise or spark.

No AC power, AC/DC adaptor

faulty, backup batteries (if

being used) depleted, IFT-

ECM slider switch in OFF

position.

Verify IFT-ECM slider switch is in ON or REM position.

Verify AC power available to junction box. Verify AC/DC

adaptor is plugged into junction box and ECM. Verify AC/

DC adaptor output voltage is between 5.7-6.3 Vdc. If

battery pack is used, check battery pack voltage is >4.2 V

(if not, replace batteries).

Shorted or loose connection

in system wiring or wiring

harness.

Verify system wiring conguration. Remove and reinstall

wiring harness that plugs into module. Check continuity

of wires in valve wiring harness. Replace any damaged

components.

Poor or no system ground. Verify black ground wire in valve harness is connected to

metal chassis of replace.

Pilot won’t light, there is no noise or spark,

2 Red/1 Green Lockout. Pilot solenoid not detected.

Check if valve harness orange wire is connected to pilot

solenoid valve. Check pilot solenoid resistance, nominal

is 40 ohms. If open or shorted, replace valve. Check valve

harness wire continuity, if open replace 6-pin harness.

Pilot won’t light, there is no noise or spark,

2 Red/2 Green Lockout. Spark coil failure. Replace ECM.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vermont Castings Stardance Series Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Vermont Castings Stardance Series

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info