Bedienungsanleitung Vibiemme Domobar Super (Seite 35 von 44) (Englisch)

783524

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

4) Tip the machine on its back and remove the two, small Phillips head screws on the bottom of the machine along

the back edge of the bottom. Stand the machine back on its feet

5) Remove the 6 screws on the outer case (three on each side). Slide the outer case off the machine

6) Replace the water reservoir’s platform and the reservoir and replace the hoses back into the reservoir.

7) Pour the de-scaling agent into the water reservoir. You will need to ﬁll it at least 1/2 full. Be sure to follow the

manufacturer’s recommendations as to the mixing of the de-scaler to the proper concentration.

8) Plug the machine in and turn the power switch to Position I only! Allow the boiler to ﬁll. Continue to the next

step after the pump stops.

WARNING: In many of the following steps, such as when pumping the de-scaler through the group-

head and removing the hoses from the water tank, splashing acid can create a safety hazard. Gloves, eye

protection, and protection for the working surface are required.

9) Place a suitable container under the grouphead and turn on the brew function to run about eight ounces out of

the machine to get the de-scaling agent through the grouphead. This also ensures that the thermosyphon pipes,

the inside of the heat exchanger and internal portions of the grouphead get de-scaled.

CAUTION: If the used de-scaling agent is poured down a drain, allow the faucet to run into the sink

to dilute the acid. Never re-use the spent acid.

10) Snap the blind ﬁlter into the portaﬁlter handle and backﬂush the machine. Turn on the brew function and

allow it to run for about ﬁve seconds. This will force the de-scaler through the over pressure relief valve. You

will see the liquid ﬂowing back into the reservoir through the secondary hose. When that takes place, turn the

machine to “0” and unplug the power cord. Leave the hoses in place and move the reservoir off to the side of

the machine and lift off the reservoir platform.

11) Remove the two Phillips head screws holding the top of the divider panel and swing it back and off the ma-

chine. Take care not to stress the wires attached to the water-level microswitch which is attached to the panel.

12) Remove the water level sensor wire by loosening the screw indicated in these two photos. Leave it discon-

nected for now. This will fool the boiler into thinking that the boiler is low on water and needs to be reﬁlled.

Set the wire off to the side where it cannot accidently

connect with any metal parts.

13) Replace the divider panel and reinstall the two Phil-

lips head screws holding the top of the divider panel

in place. Reinstall the reservoir platform and reservoir

and insert the hoses once again. If needed, reﬁll the res-

ervoir with de-scaling agent.

14) With the autoﬁll wire still disconnected, plug the

machine back in, remove the tip and O-ring from the

steam wand and place them off to the side. Place a suit-

able container under the steam wand and the hot water

wand and open the steam valve.

15) Turn the power switch to position “I” only. The au-

toﬁll is defeated and so the machine will overﬁll (com-

pletely ﬁll) the boiler. As soon as a solid stream comes

out of the steam wand, turn the power switch to Position

0 and close the steam valve.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vibiemme Domobar Super Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info