Bedienungsanleitung Victron Inverter RS 48 6000 (Seite 5 von 54) (Deutsch, Englisch, Holländisch, Französisch, Schwedisch)

785548

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

EN NL FR DE SE CZ Appendix

3.INSTALLATION

3.1 Location of the inverter

Try and keep the distance between the product and the battery to a minimum in order to minimise cable voltage losses

3.2 Connection to the battery

In order to utilize the full capacity of the product, batteries with sufficient capacity and battery cables with sufficient cross section should

be used. See table:

min

unit

Battery capacity Pb

400

Battery capacity Lithium

100

Recommended DC fuse

150

Minimum cross section (mm2) per +

and - connection terminal

0 – 2 m

mm2

2 – 5 m

mm2

Use a torque wrench with insulated box spanner in order to avoid

shorting the battery.

Maximum torque: 14 Nm

Avoid shorting the battery cables.

• Undo the two screws at the bottom of the enclosure and remove the service panel.

• Connect the battery cables.

• Tighten the nuts well for minimal contact resistance.

3.3 Wire size for connecting the inverter chassis to ground

The earth conductor from the earth lug on the chassis to ground should have at least half the cross-section of the conductors used for

the battery connection.

For best operating results, the inverter should be placed on a flat surface. To

ensure a trouble free operation of the inverter, it must be used in locations that

meet the following requirements:

a) Avoid any contact with water. Do not expose the inverter to rain or

moisture.

b) Do not place the unit in direct sunlight. Ambient air temperature should

be between -20°C and 40°C (humidity < 95% non-condensing).

c) Do not obstruct the airflow around the inverter. Leave at least 30

centimeters clearance above and below the inverter.

When the inverter is running too hot, it will shut down. When the inverter has

reached a safe temperature level the unit will automatically restart again.

This product contains potentially dangerous voltages. It should only be installed

under the supervision of a suitable qualified installer with the appropriate training,

and subject to local requirements. Please contact Victron Energy for further

information or necessary training.

Excessively high ambient temperature will result in the following:

• Reduced service life.

• Reduced charging current.

• Reduced peak capacity, or shutdown of the inverter.

Never position the appliance directly above lead-acid batteries.

The Inverter RS is suitable for wall mounting. For mounting purposes, a hook and

two holes are provided at the back of the casing. The device must be fitted

vertically for optimal cooling.

For safety purposes, this product should be installed in a heat-resistant

environment. You should prevent the presence of e.g. chemicals, synthetic

components, curtains or other textiles, etc., in the immediate vicinity.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Victron Inverter RS 48 6000 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info