Bedienungsanleitung Victron Inverter RS 48 6000 (Seite 6 von 54) (Deutsch, Englisch, Holländisch, Französisch, Schwedisch)

785548

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

3.4 Connection to the load

Never connect the output of the inverter to another AC supply, such as a household AC wall outlet or AC wave forming petrol generator.

Wave synchronising PV solar inverters can be connected to the AC output, see section on Frequency Shift Function for more

information.

The Inverter RS is a safety class I product (supplied with a ground terminal

for safety purposes). Its AC output terminals and/or grounding point on

the outside of the product must be provided with an uninterruptible

grounding point for safety purposes.

The Inverter RS is provided with a ground relay that automatically

connects the Neutral output to the chassis. This ensures the correct

operation of the internal earth leakage switch and an earth leakage circuit

breaker that is connected to the output.

─ In a fixed installation, an uninterruptable grounding can be secured by

means of the grounding wire of the AC input. Otherwise the casing

must be grounded.

─ In a mobile installation (for example, with a shore current plug),

interrupting the shore connection will simultaneously disconnect the

grounding connection. In that case, the casing must be connected to

the chassis (of the vehicle) or to the hull or grounding plate (of the

boat).

Torque: 2 Nm

3.5 VE.Direct

Used to connect a PC/laptop to configure the inverter.

3.6 VE.Can

Used to connect to a GX Device.

3.7 Bluetooth

Used to connect to the device via VictronConnect for configuration.

3.8 User I/O

3.8.1 Remote on/off connector

The remote on/off has two terminals: Remote L and Remote H. A remote on/off switch or relay contact can be connected between L and

H. Alternatively, terminal H can be switched to battery plus, or terminal L can be switched to battery minus.

Special case for Victron lithium batteries in combination with the miniBMS. When Lithium is selected in the software, the remote on/off is

changed, and that physical interface instead becomes the connection point for the allow-to-charge and allow-to-discharge wires. The

remote H input is the connection point for the allow-to-discharge control wire and must to be connected to the Load output of the

miniBMS. The remote L input is the connection point for the allow-to-charge control wire and must be connected to the Charger output

of the miniBMS. Remote on/off function is now taken over by the miniBMS.

3.8.2 Programmable relay

Programmable relay which can be set for general alarm, DC under voltage or genset start/stop function. DC rating: 4A up to 35VDC and

1A up to 70VDC

3.8.3 Voltage sense

For compensating possible cable losses during charging, two sense wires can be connected directly to the battery or to the positive and

negative distribution points. Use wire with a cross-section of 0,75mm².

During battery charging, the inverter will compensate the voltage drop over the DC cables up to a maximum of 1 Volt (i.e. 1V over the

positive connection and 1V over the negative connection). If the voltage drop threatens to become larger than 1V, the charging current

is limited in such a way that the voltage drop remains limited to 1V.

3.8.4 Temperature sensor

For temperature-compensated charging, the temperature sensor (supplied with the inverter) can be connected. The sensor is isolated

and must be fitted to the negative terminal of the battery. The temperature sensor can also be used for low temperature cut-off when

charging lithium batteries (configured in VictronConnect).

3.8.5 Programmable analog/digital input ports

The product is equipped with 2 analog/digital input ports. These ports can be configured in VictronConnect.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Victron Inverter RS 48 6000 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info