Bedienungsanleitung Viessmann Vitotronic 200 - WO1C (Seite 27 von 112) (Englisch)

813833

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

In the time programs for central heating and central

cooling you set the time phrases during which your

home is heated or cooled and to what temperature.

To do so, select an operating status for each time

phase: See chapter "Operating status for central heat-

ing/central cooling".

Factory setting: one time phase from 00:00 to 24:00 h

for every day of the week with the "Standard" operat-

ing status.

Note

■The factory setting is suitable for operation with

underfloor heating systems.

■No time program can be set for a separate cooling

circuit.

1. Extended menu:

2. "Heating" or "Heating/cooling"

3. If applicable, use / to select the required heating/

cooling circuit

4. "Time program heating" or "Time proghtg/cool-

ing"

5. Set the required time phases and operating status.

To see how to set a time program: See page 23.

Note

■Between the time phases, rooms are neither heated

nor cooled. Only the heat pump frost protection is

active ("Standby" operating status).

■When making settings, please bear in mind that your

heating system requires some time to heat or cool

the rooms to the required temperature.

Operating status for central heating/central cooling

"Standard"

■Central heating/central cooling takes place to the

standard room temperature "Set room tempera-

ture": See page 26.

"Reduced"

■Central heating/central cooling takes place to the

reduced room temperature "Set red. room temp":

See page 26.

Note

In the "Reduced" operating status, a heating/cooling

circuit is not cooled.

"Fixd value"

■Central heating takes place with the max. permissi-

ble flow temperature of the respective heating circuit,

irrespective of the outside temperature.

■Central cooling takes place with the min. flow tem-

perature of the respective heating circuit, irrespective

of the outside temperature.

■Factory settings: Your contractor may have adjusted

these values.

–Max. heating flow temperature: 40 °C

–Min. cooling flow temperature: 20 °C

Central heating/central cooling with buffer cylinder

Note

Further information regarding the different buffer cylin-

ders can be found in chapter "Terminology" in the

Appendix: See page 92.

Switching on central heating/central cooling with buffer cylinder

System with heating water buffer cylinder

For central heating, the heating water buffer cylinder

supplies your heating/cooling circuits with heat. The

heat pump heats the heating water buffer cylinder

automatically, as soon as the outside temperature

falls below the heating limit. This heating limit has

been set by your contractor.

For central cooling (if installed), the heat pump sup-

plies the cooling circuit directly, not via the heating

water buffer cylinder. Central cooling is automatically

switched on if the outside temperature rises above the

cooling limit. The cooling limit has also been set by

your contractor.

Central heating/central cooling

Setting the time program for central heating/central cooling

5817913

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Viessmann Vitotronic 200 - WO1C Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Viessmann Vitotronic 200 - WO1C

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info