Bedienungsanleitung Viessmann Vitotronic 200 - WO1C (Seite 29 von 112) (Englisch)

813833

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

Note

Above a specified outside temperature, the buffer cyl-

inder will no longer be heated, even in the "Fixd

value" operating status. Your contractor can adjust

this temperature limit.

Setting the time program for central cooling with buffer cylinder

In the time program for central cooling with buffer cylin-

der, you set the time phases in which your buffer cylin-

der is cooled and to what temperatures. In addition,

you specify whether the entire volume of the buffer cyl-

inder or just the top section is cooled.

When setting the time program, you select an operat-

ing status for each time phase: See chapter "Operating

status for cooling the buffer cylinder".

Note

This time program applies only to a heating water/cool-

ant buffer cylinder in cooling mode.

Factory setting: One time phase from 00:00 to 24:00 h

for every day of the week with the "Standard" operat-

ing status

■The time phases for cooling the buffer cylinder must

cover all time phases for central cooling (for all heat-

ing/cooling circuits).

■If you switch off heating of the heating water buffer

cylinder with the time program (all time phases are

deleted "- - : - -"), your rooms will not be heated.

■We recommend that the buffer cylinder should be

cooled continuously.

1. Extended menu:

2. "System"

3. "Time prog. coolnt buff cyl."

4. Set the required time phases and operating status.

To see how to set a time program: See page 23.

Note

■The buffer cylinder is not cooled between the time

phases. Only frost protection for the buffer cylinder is

active.

■When setting the time program, please bear in mind

that your heat pump requires some time to cool the

buffer cylinder to the required temperature.

Operating status for cooling the buffer cylinder

"Standard"

■The entire volume in the buffer cylinder is cooled to

the lowest set flow temperature for all connected

heating/cooling circuits.

■The set flow temperature of a heating/cooling circuit

results from the cooling curve, the outside tempera-

ture and the required room temperature.

"Reduced"

■The top section of the buffer cylinder is cooled to the

lowest set flow temperature for all connected heat-

ing/cooling circuits.

■The set flow temperature of a heating/cooling circuit

results from the cooling curve, the outside tempera-

ture and the required room temperature.

"Fixd value"

■The entire volume in the buffer cylinder is cooled to a

fixed temperature.

Factory setting: 20 °C

Your contractor may have adjusted this value.

■You can utilise the "Fixd value" operating status,

e.g. to cool the buffer cylinder to a lower temperature

with economical night tariff power.

Setting the heating curve/cooling curve

So that your rooms are heated or cooled optimally at

all outside temperatures, you can adjust the "Level"

and "Slope" of the "Heating curve" or the "Cooling

curve". This allows you to influence the flow tempera-

ture provided by the heat pump.

Note

Further information on setting the "Heating curve" or

"Cooling curve" can be found in chapter "Terminol-

ogy" in the Appendix: See page 92.

Central heating/central cooling

Central heating/central cooling with buffer… (cont.)

5817913

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Viessmann Vitotronic 200 - WO1C Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Viessmann Vitotronic 200 - WO1C

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info