769323
95
Zoom out
Zoom in
Vorherige Seite
1/96
Nächste Seite
PowerMaster-360 Quick user guide
D-307500 PowerMaster 360 Installer's Guide 95
PowerMaster-360 Quick user guide
Arming and disarming the system
Step
Operation
User Actions
Notes
Optional
1
Press the Partition Selection button and then
select a PARTITION (if Partition is enabled) –
used to divide the alarm system into three
independently controllable areas
followed by any
combination of ,
, or
A “protest” beep will be
heard when selecting a
partition to which no
sensors / peripherals
were enrolled.
2
Arm AWAY - used to arm the system when the
protected site is vacated entirely.
+ [ ] or enter code
ARM indicator
lights steadily during
the armed state.
ARM indicator
extinguishes during the
disarmed state.
Disarming the system
also stops the siren
alarm, irrespective of
whether the alarm was
initiated during the
armed or the disarmed
state.
Arm HOME – used to arm the system when
people are present within the protected site.
+ [ ] or enter code
Disarm (OFF) – used to restore the control panel
to the normal standby state
+ [ ] or enter code
Optional
Quick arm AWAY (If Quick Arm is enabled) –
used to arm in the AWAY state without a user
code
Quick arm HOME (If Quick Arm is enabled) –
used to arm in the HOME state without a user
code
Forced arming AWAY (system not ready) – used
to arm the alarm system in the AWAY state when
any of the system zones is disturbed
+ [ ] or enter code
to silence theprotest”
buzzer
Forced arming HOME (system not ready) – used
to arm the alarm system in the HOME state when
any of the system zones is disturbed
+ [ ] or enter code
to silence theprotest”
buzzer
Optional
3
INSTANT – used to arm in the Instant mode,
without an entry delay.
(After arming HOME/AWAY)
LATCHKEY – used for keyfob transmitters 5
through 8
Note: The factory default master user code is 1111. The code is not required if quick arming has been permitted by the
installer. Change the factory default code to a secret code without delay (see section Chapter 4, section B.4 of the
PowerMaster-360 User’s Guide).
Initiating Alarms
Alarms
Actions
Notes
Emergency alarm
( 2 sec.)
To stop the alarm, press and then key in
your valid user code.
Fire alarm
( 2 sec.)
Panic alarm
+ ( 2 sec.)
Preparing to Arm
Before arming, make sure that READY is displayed.
HH:MM READY
This indicates that all zones are secured and you may arm the system as desired.
If at least one zone is open (disturbed) the display will read:
HH:MM NOT READY
This indicates that the system is not ready for arming and in most cases that one or more
zones are not secured. However, it can also mean that an unresolved condition exists
such as certain trouble conditions, jamming etc., depending on system configuration.
95

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Visonic Powermaster-360 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info