Bedienungsanleitung Visonic Powermaster-360 (Seite 96 von 96) (Englisch)

769323

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

PowerMaster-360 Quick user guide

96 D-307500 PowerMaster 360 Installer's Guide

To review the open zones click . The details and location of the first open zone detector (usually an open

door or window sensor) will be displayed. To fix the open zone, locate the sensor and secure it (close the door

or window) – see "device locator" below. Each click of will display another open zone or trouble indication.

It is highly recommended to fix the open zone(s), thus restoring the system to the state of “ready to arm”. If you

do not know how to do this, consult your installer.

Note: To quit at any stage and to revert to the "READY" display, click .

Device Locator: The PowerMaster-360 system has a powerful device locator that helps you to identify open or

troubled devices indicated on the LCD display. While the LCD displays an open or faulty device, the LED on the

respective device flashes indicating "it's me". The "it's me" indication will appear on the device within max. 16

seconds and will last for as long as the LCD displays the device.

Zone Bypass Scheme

Bypassing permits arming only part of the system and at the same time allowing free movement of people within

certain zones when the system is armed. It is also used to temporarily remove from service faulty zones that

require repair work or to deactivate a sensor if, for example, you are decorating a room.

You can set the Zone Bypass Scheme i.e. to scroll through the list of registered (enrolled) sensors to your

PowerMaster-360 system and to Bypass (deactivate) faulty or disturbed sensors (either READY or NOT-

READY) or to Clear (reactivate) BYPASSED zones (sensors).

Once you have set a Bypass Scheme you can use the following 3 options:

To quickly clear a bypassed zone i.e. to reactivate the bypassed zone – refer to Chapter 4, section B.1 of the

PowerMaster-360 User’s Guide.

To quickly review the bypassed zones – refer to Chapter 4, section B.2 of the PowerMaster-360 User’s Guide.

To repeat (recall) the last used zone bypassing scheme – refer to Chapter 4, section B.3 of the

PowerMaster-360 User’s Guide.

Notes:

1. Zones will be bypassed throughout one disarm-arm period only. Disarming the system after arming will

suspend the entire bypassing scheme but you can recall and reuse it as described in Chapter 6, section A.3

of the KP-250 PG2 User’s Guide.

2. Fire zones cannot be bypassed.

3. If a SIM card is installed in the panel, the PowerMaster-360 displays the GSM signal strength indication, as

follows: "GSM RSSI STRONG" / "GSM RSSI GOOD" / "GSM RSSI POOR".

If a PIR camera is enrolled in the system, the control panel will read "GPRS initialize" to indicate that the

modem is undergoing initialization. This message appears at the end of all trouble messages and

immediately following the GSM signal strength indication (if a SIM card is installed).

The trouble indications (illuminated TROUBLE indicator and flashing TRBL message) are cleared once you

eliminate the cause of trouble. The following table describes the system faults and respective corrective

actions.

If you do not know how to correct a trouble situation, report it to your installer and seek his advice.

Fault

What it means

GSM NET FAIL

The cellular communicator is not able to

connect to the cellular network

COMM. FAILURE

A message could not be sent to the

monitoring station or to a private telephone

(or a message was sent but was not

acknowledged)

4. The PowerMaster-360 system allows you to authorize up to 48 people to arm and disarm the system by

providing each with a unique 4 digit personal security code (code 0000 is not allowed, minimum number of

variations of PIN codes for each user – 10000 for logical keys), and assigning them with different security

levels and functionalities. For more information, refer to Chapter 6, section B.4 of the KP-250 PG2.

5. Up to 1000 events are stored in the event log that can be reviewed via the Remote Programmer PC software

application or by remote PowerManage server.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Visonic Powermaster-360 Seite 96

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info