Bedienungsanleitung Visonic PowerMax Express (Seite 13 von 36) (Englisch)

580333

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

D-302989 13

Zone Zone Type Zone Name Chime (melody

No. Default Programmed Default Programmed Zone Name or Off) (*)

11 Interior Living Room

12 Interior Bedroom

13 Perimeter Bedroom

14 Perimeter Guest Room

15 Interior Master Bedroom

16 Perimeter Master Bedroom

17 Perimeter Laundry Room

18 Perimeter Master Bathroom

19 Perimeter Basement

20 Fire Fire

21 Fire Fire

22 Emergency Emergency

23 Emergency Emergency

24 24 h / silent Basement

25 24 h / silent Office

26 24 h / audible Attic

27 24 h / audible Den

28 non-alarm Yard

29 non-alarm Hall

30 non-alarm Utility room

* Note: All zones are CHIME OFF by default. Enter your own choice in the last column and program accordingly.

4.4 DEFINING CONTROL PANEL PARAMETERS

4.4.1 Preliminary Guidance

This mode allows you to customize the control panel and

adapt its characteristics and behavior to the requirements of

the particular user. An illustrated process is shown in Figure

4.4. In this illustration, each selected option is displayed

with a dark box at the right side. To review the options,

repeatedly click

button, until the desired

option is displayed, then click SHOW/OK button

4.4.2 Entry Delays 1&2

(Fig. 4.4, location 01, 02). Two different entry delays allow

the user to enter the protected site (while the system is in

the armed state) via 2 specific doors and routes without

causing an alarm.

Following entry, the user must disarm the control panel

before the entry delay expires. Slow-rate warning beeps

start sounding once the door is opened, until the last 10

seconds of the delay, during which the beeping rate

increases. Locations No. 1 (entry delay 1) and 2 (entry

delay 2) allow you to program the length of these delays.

Available options for each delay are: 00s, 15s, 30s, 45s,

60s, 3m and 4m.

Note: To comply with CP-01 requirements, "00s" and "15s"

options are not available.

Note: To comply with EN requirements, the entry delay

must not exceed 45 sec.

Note: To comply with UL requirements, the entry delay

must not exceed 15 sec.

4.4.3 Exit Delay

(Fig. 4.4 location 03). An exit delay allows the user to arm

the system and leave the protected site via specific routes

and doors without causing an alarm. Slow-rate warning

beeps start sounding once the arming command has been

given, until the last 10 seconds of the delay, during which

the beeping rate increases. Location No. 3 allows

programming of the exit delay length. Available options

are: 30s, 60s, 90s, 120s, 3m, and 4m.

Note: To comply with CP-01 requirements, "30s" option is

not available.

Note: To comply with UL requirements, the exit delay must

not exceed 120 sec.

4.4.4 Bell Time

(Fig. 4.4, location 04). Here you select the length of time

the bell (or siren) is allowed to function upon alarm. The

bell time starts upon activation of the siren. Once the bell

time expires, the siren is automatically shut down.

Available options are: 1, 3, 4, 8, 10, 15 and 20 minutes.

Note: To comply with EN requirements, the Bell Time

should be set to 15 min. max.

4.4.5 Abort Time

(Fig. 4.4 location 05). Here you select the length of time

allowed by the system to abort an alarm (not applicable to

alarms from FIRE, 24H SILENT, EMERGENCY, GAS,

FLOOD and TEMPERATURE zones). The

PowerMaxExpress is programmed to provide an “abort

interval” that starts upon detection of an event. During this

interval, the buzzer sounds a warning but the siren remains

inactive and the alarm is not reported. If the user disarms the

system within the allowed abort interval, the alarm is aborted.

Available options are: 00s, 15s, 30s, 45s, 60s, 2m, 3m

and 4m.

Note: To comply with CP-01 requirements, "60s", "3m" and

"4m" options are not available.

Note: To comply with UL requirements, the abort time must

not exceed 45 sec.

4.4.6 Alarm Cancel

(Fig. 4.4, location 06). Here you determine the ”cancel

alarm” period that starts upon reporting an alarm to the

central station. If the user disarms the system within that

time period, a “cancel alarm” message is sent to the

central station.

Available options are: 1, 5, 15, 60 minutes, 4 hours and

also cancel inactive.

Note: To comply with CP-01 requirements, "1 minute"

option is not available.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Visonic PowerMax Express Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Visonic PowerMax Express

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info