Bedienungsanleitung Visonic PowerMax Express (Seite 28 von 36) (Englisch)

580333

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

28 D-302989

USER SETTING

ENTER CODE

1. NEW INSTL CODE

2. ENROLLING

3. DEFINE ZONES

5. DEFINE COMM

[installer code]

INSTALLER MODE

4. DEFINE PANEL

COMMUNICATING TEL # NOT DEFINED

DOWNLOADING DIAL ATTEMPT FAIL

DOWNLOAD OK DOWNLOAD FAILED

Displayed during

dialing process

Displayed for half

a minute approx.

accompanied by sad

(failure) melody

If UL/DL server

tel. # was not

defined before

(see par. 4.5.34)

If UL/DL server

tel. # is already

defined (see

par. 4.5.34)

Dialing

failed

Download

failed

Displayed during

download process

Displayed for half

a minute approx.

accompanied by sad

(failure) melody

Displayed for half

a minute approx.

accompanied by sad

(failure) melody

Displayed for half

a minute approx.

accompanied by happy

(success) melody

9. DEFINE CUSTOM

10. DIAGNOSTICS

11. USER SETTINGS

12. FACTORY DEFLT

13. SERIAL NUMBER

14. START UL/DL

<OK> TO EXIT

WALK TEST

READY

(First display)

Figure 4.14 – Start UL/DL

4.15 WALK-TEST

This mode (see Figure 4.1a) provides you with the means to conduct a periodic test, via the walk-test menu, at least once a

week and after an alarm event.

5. TESTING PROCEDURES

5.1 Preparations

Make sure all windows and doors are closed. If all zones

are secured (undisturbed), the display should read:

READY HH:MM

If the display is “NOT READY”, query the control panel by

pressing the

OKI

button repeatedly. The source(s) of the

problem(s) will be displayed and read aloud. Take the

necessary measures to eliminate the problem(s) before

testing the system (see next paragraph).

5.2 Diagnostic Test

To verify proper function of all detectors in the system, a

comprehensive diagnostic test is required. To perform this

test, refer to figure 4.10.

5.3 Keyfob Transmitter Test

Initiate transmission from each transmitter enrolled as a

keyfob unit (according to the list in Table A2, Appendix A).

Use each transmitter to arm the control panel AWAY and

immediately disarm it. Upon pressing the keyfob unit’s

AWAY key, the ARM indicator should light.

The display should respond as follows:

ARMING AWAY



PLEASE EXIT NOW

The exit delay beeps will begin.

Press the keyfob unit’s DISARM (

) key. The ARM indicator

should extinguish, the announcement “Disarm, ready to arm"

should be heard and the display should revert to:

READY HH:MM

Test the AUX button in each keyfob in accordance with the

information noted in Table A2, Appendix A. Verify that the

AUX button performs its duty as programmed.

 If the AUX (

@) button is defined as “INSTANT”, press

the AWAY button and then the AUX button. The

response should be:

ARMING INSTANT

(alternating)

PLEASE EXIT NOW

and the exit delay beeps will start. Press the DISARM

(

) key immediately to disarm.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Visonic PowerMax Express Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Visonic PowerMax Express

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info