Bedienungsanleitung Vonroc AG503AC (Seite 7 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch)

778559

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

WWW.VONROC.COM

resulting in ﬁre, explosion or risk of injury.

Do not expose a battery pack or tool to ﬁre

or excessive temperature. Exposure to ﬁre or

temperature above 130 °C may cause explosion.

NOTE The temperature „130 °C“ can be replaced

by the temperature „265 °F“.

Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range speciﬁed in the instructions.

Charging improperly or at temperatures outside

the speciﬁed range may damage the battery and

increase the risk of ﬁre.

6) Service

a) Have your power tool serviced by a qualiﬁed

repair person using only identical replacement

parts. This will ensure that the safety of the

power tool is maintained.

Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorized service providers.

SAFETY WARNINGS COMMON FOR GRINDING

OR ABRASIVE CUTTINGOFF OPERATIONS

a) This power tool is intended to function as a grind-

er tool. Read all safety warnings, instructions,

illustrations and speciﬁcations provided with this

power tool. Failure to follow all instructions listed

below may result in electric shock, ﬁre and/or

serious injury.

b) Operations such as sanding, wire brushing,

polishing are not recommended to be performed

with this power tool. Operations for which the

power tool was not designed may create a hazard

and cause personal injury.

c) Do not use accessories which are not speciﬁ-

cally designed and recommended by the tool

manufacturer. Just because the accessory can

be attached to your power tool, it does not assure

safe operation.

d) The rated speed of the accessory must be at

least equal to the maximum speed marked on the

power tool. Accessories running faster than their

rated speed can break and ﬂy apart.

e) The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories

cannot be adequately guarded or controlled.

f) Threaded mounting of accessories must match

the grinder spindle thread. For accessories

mounted by ﬂanges, the arbour hole of the acces-

sory must ﬁt the locating diameter of the ﬂange.

Accessories that do not match the mounting hard-

ware of the power tool will run out of balance,

vibrate excessively and may cause loss of control.

g) Do not use a damaged accessory. Before each

use inspect the accessory such as abrasive

wheels for chips and cracks, backing pad for

cracks, tear or excess wear, wire brush for loose

or cracked wires. If power tool or accessory is

dropped, inspect for damage or install an undam-

aged accessory. After inspecting and installing an

accessory, position yourself and bystanders away

from the plane of the rotating accessory and run

the power tool at maximum no-load speed for one

minute. Damaged accessories will normally break

apart during this test time.

h) Wear personal protective equipment. Depending

on application, use face shield, safety goggles or

safety glasses. As appropriate, wear dust mask,

hearing protectors, gloves and workshop apron

capable of stopping small abrasive or workpiece

fragments. The eye protection must be capable

of stopping ﬂying debris generated by various

operations. The dust mask or respirator must be

capable of ﬁltrating particles generated by your

operation. Prolonged exposure to high intensity

noise may cause hearing loss.

i) Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment. Fragments of

workpiece or of a broken accessory may ﬂy away

and cause injury beyond immediate area of opera-

tion.

j) Hold the power tool by insulated gripping sur-

faces only, when performing an operation where

the cutting accessory may contact hidden wiring

or its own cord. Cutting accessory contacting a

“live” wire may make exposed metal parts of the

power tool “live” and could give the operator an

electric shock.

k) Position the cord clear of the spinning acces-

sory. If you lose control, the cord may be cut or

snagged and your hand or arm may be pulled into

the spinning accessory.

l) Never lay the power tool down until the accessory

has come to a complete stop. The spinning acces-

sory may grab the surface and pull the power tool

out of your control.

m) Do not run the power tool while carrying it at

your side. Accidental contact with the spinning

accessory could snag your clothing, pulling the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc AG503AC Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info