Bedienungsanleitung Vonroc AG503AC (Seite 9 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch)

778559

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

WWW.VONROC.COM

ning wheel and the power tool directly at you.

c) When wheel is binding or when interrupting a

cut for any reason, switch off the power tool

and hold the power tool motionless until the

wheel comes to a complete stop. Never attempt

to remove the cut-off wheel from the cut while

the wheel is in motion otherwise kickback may

occur. Investigate and take corrective action to

eliminate the cause of wheel binding.

d) Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed and

carefully re-enter the cut. The wheel may bind,

walk up or kickback if the power tool is restart-

ed in the workpiece.

e) Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kick-

back. Large workpieces tend to sag under their

own weight. Supports must be placed under the

workpiece near the line of cut and near the edge

of the workpiece on both sides of the wheel.

f) Use extra caution when making a “pocket cut”

into existing walls or other blind areas. The

protruding wheel may cut gas or water pipes,

electrical wiring or objects that can cause kick-

back.

Electrical safety

Always check that the voltage of the power

supply corresponds to the voltage on the

rating plate.

• Do not use the machine if the mains cable or

the mains plug is damaged.

•

Only use extension cables that are suitable for

the power rating of the machine with a minimum

thickness of 1.5 mm

. If you use an extension

cable reel, always fully unroll the cable.

2. MACHINE INFORMATION

Intended use

Your angle grinder has been designed for grinding

masonry and steel materials without the use of

water. For cutting, a special protection guard must

be used (not included). Fig. D2.

Not suitable for construction site usage.

TECHNICAL SPECIFICATIONS

Model No. AG503AC

Mains voltage 220-240V~

Mains frequency 50Hz

Power input 2400W

No-load speed 6800 /min

Grinding disc

Diameter:

Bore:

230 mm

22.2 mm

Spindle thread M14

Weight 5.5 kg

Sound pressure level L

97.6 dB(A), K=3dB(A)

Acoustic power level L

108.6 dB(A), K=3dB(A)

Vibration

Main handle

11.598 m/s, K=1.5 m/s

Auxiliary handle 5.618 m/s, K=1.5 m/s

Wear hearing protection.

Vibration level

The vibration emission level stated in this instruction

manual has been measured in accordance with a

standardized test given in EN60745; it may be used

to compare one tool with another and as a prelim-

inary assessment of exposure to vibration when

using the tool for the applications mentioned.

• Using the tool for different applications, or with

different or poorly maintained accessories, may

signiﬁcantly increase the exposure level.

• The times when the tool is switched off or when

it is running but not actually doing the job, may

signiﬁcantly reduce the exposure level.

Protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work patterns.

DESCRIPTION

The numbers in the text refer to the diagrams on

page 2-3.

1. Spindle lock button

2. Allen screw

3. Protection guard

4. Carbon brush cover

5. On/Off switch

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc AG503AC Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info