Bedienungsanleitung Vonroc CD506DC (Seite 7 von 48) (Deutsch, Englisch, Holländisch, Französisch, Spanisch, Polnisch)

763912

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

WWW.VONROC.COM

Warning! This power tool produces an

electromagnetic ﬁeld during operation.

This ﬁeld may under some circumstances

interfere with active or passive medical

implants. To reduce the risk of serious or

fatal injury, we recommend persons with

medical implants to consult their physician

and the medical implant manufacturer

before operating this power tool.

2. MACHINE INFORMATION

Intended use

This screw driver is intended for driving in and

loosening screws.

TECHNICAL SPECIFICATIONS

Model No CD506DC

Output of charger 5V DC Max. 1000mA

Rechargeable Battery pack 4V Li-ion 320 mAh

Battery charging time 70-90 minutes

Chuck capacity 1/8" (4mm) hex

No load speed 120 /min

Sound pressure level L

39.5 dB(A) K=3 dB(A)

Sound power level L

50.5 dB(A) K=3 dB(A)

Hand-arm vibration a

(screw driving without impact) 0.149 m/s

K=1.5 m/s

Vibration level

The vibration emission level stated in this instructi-

on manual has been measured in accordance with

a standardized test given in EN62841; it may be

used to compare one tool with another and as a

preliminary assessment of exposure to vibration

when using the tool for the applications mentioned.

• Using the tool for different applications, or with

different or poorly maintained accessories, may

signiﬁcantly increase the exposure level.

• The times when the tool is switched off or when

it is running but not actually doing the job, may

signiﬁcantly reduce the exposure level.

Protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work patterns.

DESCRIPTION

The numbers in the text refer to the diagrams on

pages 2-3.

1. Machine

2. Battery indication light

3. Work light button

4A . Counterclockwise switch

4B. Clockwise switch

5. Base cover

6. Work light

7. Bit holder

8. Screwdriver bit

9. Base

10. Charging socket

3. OPERATING

The machine must be charged before ﬁrst

use.

Charging the machine (Fig. B)

In order to charge the machine, insert the small

micro-USB plug of the charger cable into the char-

ging socket (10) on the side of the machine (1).

Subsequently plug the large USB plug connector

into a USB outlet. The battery indication light (2)

will show the charging progress.

Fully charging the battery may take up to 70-90

minutes.

Fitting and removing drills or screwdriver bits (Fig. C)

The machine bit holder (7) is suitable for drills

and screwdriver bits with a standard 1/8” (4mm)

hexagonal shaft. To ﬁt a screwdriver bit:

• Insert the screw driver bit (8) into the machine’s

bit holder (7), it will be hold by a magnet.

• The screw driver bit can be removed by pulling

it out of the bit holder again.

Switching the machine on and off (Fig. A)

• Pressing the Counterclockwise switch (4A) will

activate the machine to loosen screws.

• Pressing the Clockwise switch (4B) will activate

the machine to tighten screws.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc CD506DC Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info