Bedienungsanleitung Vonroc ET502AC (Seite 7 von 40) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

764004

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

WWW.VONROC.COM

Vibration level

The vibration emission level stated in this instruc-

tion manual has been measured in accordance

with a standardized test given in EN60745; it may

be used to compare one tool with another and as

a preliminary assessment of exposure to vibration

when using the tool for the applications mentioned.

• Using the tool for different applications, or with

different or poorly maintained accessories, may

signiﬁcantly increase the exposure level.

• The times when the tool is switched off or when

it is running but not actually doing the job, may

signiﬁcantly reduce the exposure level.

Protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work patterns.

DESCRIPTION

The numbers in the text refer to the diagrams on

pages 2 - 3.

1. Reload lever

2. Cartridge shaft

3. Switch

4. Lock on button

5. Top

6. lock off button

7. Cartridge ﬁlling level window

8. Safety pin

3. OPERATION

Application (Fig. B)

For this tool, use one of the following length for

staples or nails:

• Staples: 6 up to 14 mm

• Nails: 15 mm

Loading the nails or staples (Fig. 3)

• Choose the correct nail or staple for the job.

• Hold the tacker with bottom upwards.

• Open de cartridge shaft (2) by slightly pressing

the reload lever (1)

• Pull the reload lever backwards to open the

cartridge shaft(2).

For nails:

•

Place the nails upside down against the left side

of the cartridge shaft (2). The left side also shows

a nail-symbol on the cartridge shaft, see ﬁg.4

For staples:

• Place the staples upside down in the cartridge

shaft (2).

• Push the reload lever to fully close the cartridge

shaft.

Before loading the tacker, make sure the

machine is in lock on position and it is

disconnected from the mains supply.

Never load staples and nail at the same time.

Checking the cartridge shaft

The cartridge ﬁlling level window (7) indicates the

amount of staples/nails inside the cartridge shaft.

Using the tacker

After every load test the machine on a piece

of scrape.

• Press the Lock Off switch (6) to unlock the

machine.

NOTE: The machine does not work when Lock on

switch (4) is pressed. Even though connected to

the mains supply.

•

Press the lock On switch (4) to lock the machine.

NOTE: When not in use, press the lock On switch

to lock the machine and disconnect from the

mains supply.

NOTE: Always store in Lock on (4) position.

Placing the tool

1. Place the tool on workpiece at the spot where

the staple or nail should be located.

2. Press the tool down ﬁrmly by pressing the ma-

chine on the top (5) with one hand.

3. Use your other hand to operate the switch (3).

4. By pressing the machine down ﬁrmly you lift the

safety of the machine.

Warning! The safety of the machine will be

lifted when pressure is applied to the safety

pin (8) on the bottom of the machine.

Always make sure the tacker mouth is in

direct contact with the material when

pressing the switch.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc ET502AC Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info