Bedienungsanleitung Vonroc ET502AC (Seite 8 von 40) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

764004

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

WWW.VONROC.COM

Stapling

• Press the switch (3).

The tool will cause a re bound because of

the impact it operates with. Keep this in

mind. For long nails and staples this can

cause wrong stapling or nailing. When

backpressure is applied wrong stapling or

nailing can be avoided.

4. MAINTENANCE

Make sure that the machine is not live when

carrying out maintenance work on the motor.

This machine has been designed to operate over a

long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon

proper machine care and regular cleaning.

Malfunction

Should the machine fail to function correctly, a

number of possible causes and the appropriate

solutions are given below:

In case a staple or nail is jammed in the tool, follow

the procedure below:

• Place the machine in lock position (4)

• Disconnect the tool

•

Open the cartridge shaft (2) by pulling the reload

lever (1) and let the jammed nails/staples fall out.

• Reload the machine, see chapter “ Loading the

nails or staples” for instructions.

• Test the machine on a piece of scrap.

Cleaning

Regularly clean the device’s casing with a soft

cloth, preferably after each use. Keep the fan slits

free of dust and dirt. Remove tough dirt using a

soft cloth, dampened with soapy water. Do not use

solvents such as benzene, alcohol, ammonia, etc.,

which might damage the plastic parts.

ENVIRONMENT

Faulty and/or discarded electrical or

electronic apparatus have to be collected at

the appropriate recycling locations.

Only for EC countries

Do not dispose of power tools into domestic waste.

According to the European Guideline 2012/19/

EC for Waste Electrical and Electronic Equipment

and its implementation into national right, power

tools that are no longer usable must be collected

separately and disposed of in an environmentally

friendly way.

WARRANTY

VONROC products are developed to the highest

quality standards and are guaranteed free of

defects in both materials and workmanship for the

period lawfully stipulated starting from the date of

original purchase. Should the product develop any

failure during this period due to defective material

and/or workmanship then contact VONROC directly.

The following circumstances are excluded from this

guarantee:

• Repairs and or alterations have been made

or attempted to the machine by unauthorized

service centers;

• Normal wear and tear;

• The tool has been abused, misused or

improperly maintained;

• Non-original spare parts have been used.

This constitutes the sole warranty made by compa-

ny either expressed or implied. There are no other

warranties expressed or implied which extend

beyond the face hereof, herein, including the

implied warranties of merchantability and ﬁtness

for a particular purpose. In no event shall VONROC

be liable for any incidental or consequential dama-

ges. The dealers remedies shall be limited to

repair or replacement of nonconforming units or

parts.

The product and the user manual are subject to

change. Speciﬁcations can be changed without

further notice.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc ET502AC Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info