Bedienungsanleitung Vonroc LL501DC (Seite 7 von 40) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

764066

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

7WWW.VONROC.COM

Danger of injury due to defective compo-

nents! The product must only be put into

operation if no defects are found. Ensure

that any defective parts are replaced before

the product is used again.

WARNING! Risk of injury due to laser beam!

Never direct the laser beam towards people,

other living creatures or reﬂecting surfaces.

Check the device:

• Make sure all parts are ﬁtted on the machine

ﬁrmly.

• Check whether there are any visible defects:

broken parts, cracks, etc.

• Check the accuracy when it is the ﬁrst time you

are using the laser or when the laser has not

been checked for accuracy in a while.

• Also check the accuracy when the laser may

have been dropped.

Self- levelling mode (Fig. A, D1)

The lasers are aligned automatically by the pen-

dulum so that the vertical and horizontal lines are

displayed level on the wall.

1. Place the laser on a ﬂat surface or ﬁt it to the

universal clamp (7) or tripod (not included) and

fasten it as described above.

2. Slide the lock switch (2) to the left to switch the

device on. The operating mode button (1) is illu-

minated in green. If the operating mode button

(1) is illuminated in red and the laser ﬂashes,

the permissible inclination range of 5 degrees is

exceeded. Position the device horizontally until

the operating mode button lights green.

3. To switch off, slide the lock switch to the right.

The laser switches off and the pendulum will be

locked.

Switch the measuring tool off when

transporting it. The pendulum unit is locked

when the tool is switched off, as it can

otherwise be damaged.

Manual mode (Fig. A, D2)

The laser can be aligned manually to the angle you

require, to enable for example a diagonal line to be

displayed.

1. Place the laser on a ﬂat surface or ﬁt it to the

universal clamp (7) or tripod (not included) and

fasten it as described above.

2. Check if the lock switch (2) is set to the right. If

not, slide the lock switch (2) to the right.

3. Press the operating mode button (1) to switch

the laser on and the operating mode button (1)

lights up red, because the pendulum is blocked.

4. Now you can tilt the laser to the angle you re-

quire, so that the lines are displayed diagonally

on the wall as shown in Fig. D2.

5. To switch off , press the operating mode button

(1).

5. MAINTENANCE

Accuracy check

Only the centre of the laser line must be

used for marking. The width of the laser line

changes depending on the distance.

Quick horizontal line check (Fig. A, E1)

1. Set the device at approximately 5 meters from

the wall.

2. Slide the lock switch (2) to the left to switch the

device on. The operating mode button (1) is illu-

minated in green. If the operating mode button

(1) is illuminated in red and the laser ﬂashes,

the permissible inclination range of 5 degrees is

exceeded. Position the device horizontally.

3. After it self-levels, make a horizontal mark on the

wall as shown in ﬁgure E1. Label this as point A.

4. Turn the laser 2.5 m to the right.

5. Turn the laser on, and after it self-levels, make a

horizontal mark on the wall. Label this as point

B as shown in ﬁgure E1. When points A and

B are more than 2.5mm apart from a vertical

perspective, a calibration check is necessary.

Quick vertical line check (Fig. A, E2):

1. Set the device at approximately 5 meters from

the wall.

2. Hang a 2.5 meter rope on the wall with a weight

on the end of the rope as shown in ﬁgure E2.

The rope must be able to swing freely.

3. Slide the lock switch (2) to the left to switch the

device on. Position the vertical line next to the

wire. The operating mode button (1) is illumi-

nated in green. If the operating mode button (1)

is illuminated in red and the laser ﬂashes, the

permissible inclination range of 5 degrees is

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc LL501DC Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info