Bedienungsanleitung Vonroc LR501DC (Seite 5 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

764124

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

WWW.VONROC.COM

vice and protect yourself from dripping wax!

• Before each use check the unit and accessories

for damage and function.

• Do not disassemble, burn, or short-circuit bat-

teries and do not attempt to recharge nonre-

chargeable batteries.

• Do not disassemble the unit or attempt to repair

it yourself. It does not contain parts serviceable

by you. In the case of questions or problems,

turn to our customer support.

2. MACHINE INFORMATION

Intended use

The device is intended for repairing surfaces of

laminate, parquet, cork, hardwood ﬂoors, wood

and plastic by melting a suitable wax. The device

is not allowed for melting other materials. The

appliance is intended exclusively for domestic

use. Do not use the appliance for commercial or

industrial applications. Operation is only permitted

in a dry environment; contact with moisture must

be avoided at all times.

TECHNICAL SPECIFICATIONS

Model No. LR501DC

Battery 2x 1.5V LR6 Size AA

Weight (without batteries) 42 g

Voltage DC 3V

Power input 3W

DESCRIPTION

The numbers in the text refer to the diagrams on

pages 2-3.

1. Wax melter

2. Wax melting tip

3. Protection cap

4. On/Off switch

5. Heat button

6. LED light

7. Battery compartment

8. Cleaning scraper with curvature

9. Flattening scraper

10. Abrasive sponge

11. Cleaning cloth

12. Wax sticks (A to K)

3. ASSEMBLY

Inserting the batteries (Fig. A2)

This device requires 2x 1.5 V batteries, Type AA/

LR6/Alkaline, for operation.

• Open the battery compartment (7) on the back

side of the device.

• Place the batteries into the battery compart-

ment, following the polarity details as depicted

in it.

• Close and secure the battery compartment.

Replace the batteries when reaching the

operating temperature requires more than

60 seconds.

4. OPERATION

Switching the device ON/OFF

• To switch the appliance on, place the On/Off

switch (4) at the position “ON”.

• Press and hold the heat button (5) to heat up

the wax melting tip (2).

Warning! Do not press the heat button (5)

while switching the on/off switch (4).

• Red LED (6) lights up when melting tip is heat-

ing.

• When releasing heat button (5) the wax melting

tip will cool down and the light turns off.

• To switch the appliance off, place the On/Off

switch (4) at the position “OFF”.

• After use always place the protection cap (3)

back on the device.

Avoid turning on the device accidentally.

Make sure the device is turned off before

laying it down or storing it.

Preparation of the damaged area (Fig. B)

• The damaged area must be cleaned and ﬂat-

tened before repairing.

• Clean the damaged area with the sharp edge of

the ﬂattening scraper (9).

• Remove all loose residue.

Colour selection to match damaged area (Fig. C)

• Select the matching colour tone.

Tip! When in doubt between two colours, start

with lighter colour.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc LR501DC Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info